Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TES TDS-55-P
Summary of Contents for TES TDS-55-P
- Page 1 User Manual Version 2.0 2018/07 TDS-55-P Touch Monitor TDS-55-P standard version...
- Page 2 TES Touch Embedded Solutions Inc.. The information in this document is subject to change without notice. TES makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose.
- Page 3 Compliance Information For FCC (USA) This equipment has been tested and fund to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. There limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 4 Usage Notice Warning - To prevent the risk of fire or shock hazards, and do not expose the product to moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions follow all warnings, precautions and maintenance as recommended in this user’s Please manual to maximize the life of your unit.
-
Page 5: Table Of Contents
Table of Contents Chapter 1 ........................5 1.1 Overview ........................6 1.2 Feature ........................6 1.3 Specifications ......................6 1.4 Block Diagram ......................7 1.5 Interface Connectors ....................7 1.5.1 Power Connector ....................7 1.5.2 Video Signal Connector ..................8 1.5.3 Signal Connector .................... -
Page 6: Chapter 1
Chapter 1 Product Introduction... -
Page 7: Overview
1.1 Overview The TDS-55A Series is a 55" large size thin-film transistor (TFT) liquid crystal display (LCD).This unit is to be used as commercial and light industrial equipment only. 1.2 Feature 4K2K High Resolution Display Dynamic Touch Sensitivity Technology Supports up to 6mm Thickness glass ... -
Page 8: Block Diagram
1.4 Block Diagram This section describes the electrical requirements of the monitor. The block diagram in figure 1 illustrates the various electrical sub-systems. 1.5 Interface Connectors 1.5.1 Power Connector The AC converter shall have an IEC320 type male power receptacle for connection to AC mains power. -
Page 9: Video Signal Connector
1.5.2 Video Signal Connector The video signal input via HDMI female connector. Connector Pin Assignment: Signal Signal TMDS Data2+ TMDS Clock Shield TMDS Data2 Shield TMDS Clock– TMDS Data2– TMDS Data1+ Reserved (N.C. on device) TMDS Data1 Shield TMDS Data1– TMDS Data0+ DDC/CEC Ground TMDS Data0 Shield... -
Page 10: Signal Connector
The video signal input via Display Port (1.2) connector. Connector Pin Assignment: Signal ML_Lane 3(n) Data3 - Signal ground ML_Lane 3(p) Data3 + ML_Lane 2(n) Data2 - Signal ground ML_Lane 2(p) Data2 + ML_Lane 1(n) Data1 - Signal ground ML_Lane 1(p) Data1 + ML_Lane 0(n) Data0 - Signal ground ML_Lane 0(p) Data0 +... - Page 11 Audio Line in / Line out connector...
-
Page 12: Package Overview
This product is intended to be supplied by a AC-in Power source, rated 100V~240V, 1.3~2.5A 50/60Hz minimum, Tma = 40 degree C minimum, and the altitude of operation = 3048m minimum. If it needs further assistance with purchasing the power source, please contact to TES for further information. -
Page 13: Chapter 2
Chapter 2 Product Installation... -
Page 14: About Vesa Mount
The VESA mount is located on the back of this unit. Warming! Please select the TES original screws! The distance between the back cover surface and the bottom of the screw hole is 6~7 mm. Please use M5 screws diameter with proper length to mount your... -
Page 15: Install The Vesa Screw
2.1.1 Install the VESA screw Note: Please install/ dismantle the product when the device is in the shutdown state. Step 1: Fasten two M6 screws nut into the VESA hole The length of screw nut is 30mm... -
Page 16: About General Mounting Information
2.2 About General Mounting Information The following two mounting orientations are supported: Landscape and portrait mode. For optimal touch performance, ensure that the monitor is supported fully and is as flat as possible. 2.2.1 Landscape 2.2.2 Portrait... -
Page 17: On-Screen Display
2.3 On-Screen Display The TDS-55 Lite series provide side panel controls. And the following is OSD function table: Menu off status Menu on status MENU Menu appear Menu disappear/ return to main item ▲ Brightness Main item select up/ Adjust up ▼... -
Page 18: Osd Function Description
a. Without the OSD menu on screen, press and hold “Menu” key ,and press “UP” once then release “MENU” key. The factory menu will appear on the screen. d. Use the "UP” and “DOWN key to select main functions, then press “SELECT” to enter sub menu for adjusting (or setting) those values. -
Page 19: Timing Table Chart
2.3.2 Timing Table Chart H-Freq. Bandwidth Polarity Mode Resolution (KHz) (MHz) VGA 640x480 60Hz 31.47 25.175 VESA 800x600 60Hz 37.88 VESA 1024x768 60Hz 48.36 VESA 1280x720 60Hz 44.772 74.5 VESA 1280x768 60Hz 47.776 79.5 VESA 1280x1024 60Hz VESA 1280x960 60Hz VESA 1440x900 60Hz 106.5 VESA 1360x768 60Hz... -
Page 20: Dimension
2.4 Dimension 2.4.1 Front View 2.4.2 Side View... -
Page 21: Rear View
2.4.3 Rear View 2.4.4 Back View... -
Page 22: Appendix
Appendix... - Page 23 Declaration of the Presence Condition of the Restricted Substances Marking 設備名稱：觸控螢幕 型號（型式）：TDS-55 Type designation (Type) ：TDS-55 Equipment name：Touch Monitor 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 Unit 六價鉻 多溴聯苯 多溴二苯醚 鉛 汞 鎘 Cadmium Hexavalent Polybrominated Polybrominated Lead Mercury (Cd) chromium biphenyls...
Need help?
Do you have a question about the TDS-55-P and is the answer not in the manual?
Questions and answers