Related Manuals for HBX SNO-0111
Summary of Contents for HBX SNO-0111
- Page 1 Installation Manual Socket and Cover Plate 0111 Snowmelt Sensor 0110 HBX Control Systems Inc.
-
Page 2: Table Of Contents
H B X S n o w m e l t S e n s o r TABLE OF CONTENTS Introduction .................... 3 Description ....................3 Safety Symbols & Warnings ..............3 Receipt & Inspection ................3 Technical Data ..................4 Dimensions ....................4 Installation and Wiring ................5-8 Installation ....................5... -
Page 3: Introduction
H B X S n o w m e l t S e n s o r HBX SNO-0111/ SNO-0100 SNOWMELT SENSOR/ SOCKET AND COVER PLATE INTRODUCTION This manual will help with the installation, parameter setting, troubleshooting and general maintenance requirements for the snowmelt sensor, socket and cover plate. -
Page 4: Technical Data
H B X S n o w m e l t S e n s o r TECHNICAL DATA AND DIMENSIONS Nameplate Information: The exterior label contains specific information unique to your HBX Snowmelt Sensor and identifies TECHNICAL DATA some of the basic features. The label displays the serial number which will match the serial number... -
Page 5: Installation And Wiring
Failure to do so may result in the sensor not making proper contact and not reading the slab temperature properly. Figure 3 - Tightening the socket onto the rebar © HBX Control Systems Inc. 2014 Page 5... - Page 6 H B X S n o w m e l t S e n s o r b) Placing Concrete A plastic cover is provided with the socket to prevent it from being accidentally filled with concrete. The plastic cover is the same thickness as the sensor flange. This allows the finished surface of the concrete to be toweled flush with the cover. The cover must be installed prior to placing the concrete.
-
Page 7: Wiring
In the unlikely event that the sensor becomes inoperable carefully remove it from the socket and follow the installation procedure to install a new sensor. © HBX Control Systems Inc. 2014 Page 7... - Page 8 EXPANSION MODULE SNO-0100 4-20mA DO NOT 1-10v CONNECT POWER HERE TM TM H B X S n o w m e l t S e n s o r SNO-0110 - DRAWING 003 SNO-0110 - DRAWING 004 SLAB SNOW/ICE SENSOR WIRING WITH A REMOTE INSTALL - SNOW/ICE SENSOR WITH SNO-0550 A SNO-0550...
-
Page 9: Testing And Troubleshooting Procedure
With the sensor plugged into the control (make sure heater is ON) check the voltage between Green and Black. The reading should be around 0.5-1.0 VDC without snow on the optical sensor and 2.0-3.0 VDC with 100% snow. © HBX Control Systems Inc. 2014 Page 9... -
Page 10: Sno-0110 - Troubleshooting
On the boiler contacts or injection pump or system pump. Solution: Verify that the system sensor connection is as described in the Installation Manual of the SNO-0111/SNO- 0110. -
Page 11: Warranty Information
HBX Controls warrants each of its products to be free from defects in workmanship and materials under normal use and service for a period of 24 months from date of manufacture or 12 months from date of purchase from an HBX Authorized Dealer, if within the above documented period after date of manufacture. - Page 12 Phone: +1 (403) 720-0029 Fax: +1 (403) 720-0054 Email: inf o @ hbxcontrols.com Web: www.hbxcontrols.com Manual Version 3.8 HBX Control Systems Inc. 4516 - 112 Avenue SE © HBX Control Systems Inc. 2014 Calgary, AB T2C 2K2...
Need help?
Do you have a question about the SNO-0111 and is the answer not in the manual?
Questions and answers