Advertisement
other entity, or individual. (The telephone number provided may
not be a 900 number or any other number for which charges
exceed local or long-distance transmission charges.) In order to
program this information into your modem, refer to the BVRP
software on the CD-ROM that shipped with your modem. If you are
using a different communication software program, refer to its
manual.
Radio and Television Interference:
This equipment generates, uses, and can radiate radio frequency
energy. If this equipment is not installed and used in accordance
with the manufacturer's instructions, it may cause interference to
radio and television communications. The modem has been tested
and found to comply with the limits for a Class B computing device
in accordance with the specifications in Part 15 of FCC rules, which
are designed to provide reasonable protection against such
interference in a residential installation.
For Canadian Modem Users
Industry Canada (IC)
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the interference-
causing equipment standard entitled Digital Apparatus, ICES-003
of Industry Canada.
NOTICE:
The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all devices does not exceed 5. The Ringer
Equivalence Number is located on the bottom of the modem.
NOTICE:
The Industry Canada (IC) label identifies certified
equipment. This certification means the equipment meets certain
telecommunications network protective, operational, and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. In some
cases, the company's inside wiring associated with a single-line,
individual service may be extended by means of a certified
connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions may
not prevent degradation of service in some situations. Currently,
telecommunication companies do not allow users to connect their
equipment to jacks except in precise situations that are spelled
out in tariffing arrangements with those companies. Repairs to
certified equipment should be coordinated by a representative
designated by the supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to
disconnect the equipment.
«AVIS :
Cet appareil numérique respecte les limites de bruits
radioélectriques applicables aux appareils numériques de classe
B prescrites dans la norme sur le matériel brouilleur : "Appareils
Numériques", NMB-003 édictée par l'Industrie Canada.
L'étiquette d'Industrie Canada identifie le matériel homologué.
Cette étiquette certifie que le matériel est conforme aux normes
de protection, d'exploitation et de sécurité des réseaux de
télécommunications, comme le prescrivent les documents
concernant les exigences techniques relatives au matériel
terminal. Le Ministère n'assure toutefois pas que le matériel
fonctionnera à la satisfaction de l'utilisateur.
Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est
permis de le raccorder aux installations de l'entreprise locale de
télécommunication. Le matériel doit également être installé en
suivant une méthode acceptée de raccordement. L'abonné ne
doit pas oublier qu'il est possible que la conformité aux
conditions énoncées cidessus n'empêche pas la dégradation du
service dans certaines situations. Les réparations de matériel
homologué doivent être coordonnées par un représentant
désigné par le fournisseur. L'entreprise de télécommunications
peut demander à l'utilisateur de débrancher un appareil à la
suite de réparations ou de modifications effectuées par
l'utilisateur ou à cause de mauvaisfonctionnement.
Centre de guarantie et de service après-vente:
U.S. Robotics
Unit-100, 13751 Mayfield Pl.
Richmond, B.C. Canada V6V 2G9
U.S. Robotics Corporation Limited
Warranty
HARDWARE: U.S. Robotics warrants to the end user
("Customer") that this hardware product will be free from
defects in workmanship and materials, under normal use and
service, for the following length of time from the date of
purchase from U.S. Robotics or its authorized reseller:
Two (2) years
U.S. Robotics' sole obligation under this express warranty
shall be, at U.S. Robotics' option and expense, to repair the
defective product or part, deliver to Customer an equivalent
product or part to replace the defective item, or if neither of
the two foregoing options is reasonably available, U.S.
Robotics may, in its sole discretion, refund to Customer the
purchase price paid for the defective product. All products
that are replaced will become the property of U.S. Robotics.
Replacement products may be new or reconditioned. U.S.
Robotics warrants any replaced or repaired product or part
for ninety (90) days from shipment, or the remainder of the
initial warranty period, whichever is longer.
SOFTWARE: U.S. Robotics warrants to Customer that each
software program licensed from it will perform in substantial
conformance to its program specifications, for a period of
ninety (90) days from the date of purchase from U.S.
Robotics or its authorized reseller. U.S. Robotics warrants
Advertisement
