Table of Contents
Advertisement
Quick Links
SUMP PUMP RANGE
Installation Operating
Maintenance Instructions
& Warranty Conditions
IMPORTANT
This instruction
manual must be
read and adhered
to prior to
installating and/or
operating the
pump/s.
SUBMERSIBLE
For safety
reasons, persons
who have not read
these instructions
should not be
authorised to use
the pump.
The Installer must
provide a copy of
this manual to the
Operator of the
pump/s.
While this booklet
is comprehensive,
it is not exhaustive.
Therefore, if you
need clarification
of any of the
information
contained herein,
please contact us.
Advertisement
Table of Contents
Related Manuals for Ultraflow UMDZ7500/80/30
Summary of Contents for Ultraflow UMDZ7500/80/30
- Page 1 SUBMERSIBLE SUMP PUMP RANGE Installation Operating Maintenance Instructions & Warranty Conditions IMPORTANT This instruction For safety The Installer must While this booklet manual must be reasons, persons provide a copy of is comprehensive, read and adhered who have not read this manual to the it is not exhaustive.
-
Page 2: Product Specifications
PRIOR TO INSTALLATION & OPERATION The Installer must consult a WHS supervisor PRODUCT SPECIFICATIONS and/or adhere to all relevant criteria and regulations. The installer should consult an CAUTION: engineer for site assessment and correct installation methods. • Do not operate this product under any When the pump is delivered, first perform the conditions other than those for which it following checks. -
Page 3: Preparing For Installation
INSTALLATION CAUTION: PREPARING FOR INSTALLATION • Do not use pump in liquids other than Before installing the pump at a work site, you water, sewage, or chemically stable will need to have the following tools and wastewater. Do not use pump in oil, instruments ready. - Page 4 4 Where a float switch is attached to the WARNING: pump, ensure the float switch is free to operate without interfering with tank • When installing the pump, pay close walls, pipe work etc. attention to its centre of gravity and weight.
-
Page 5: Electrical Wiring
8 To prevent the pump strainer stand CAUTION: from becoming submerged in mud, causing it to suck in debris, mount it on • If large quantities of earth are sucked a block or firm base. up, damage resulting from erosion in the pump can lead to electrical leakage and shock. -
Page 6: Power Cable
CAUTION: or unexpected starting of the pump, leading to injury or death. • Draw power from a dedicated power outlet. Sharing the outlet with other equipment may overheat the branch WARNING: outlet and could result in a fire. • Before inserting the power supply plug - When using a three pin plug, make certain the power supply is connect as described in the... -
Page 7: Electrical Circuit Diagrams
• If it is necessary to submerse the • Do not allow power cable leads or connection leads of the power cable in power supply plug to become wet. water, first seal the leads completely in • Make sure that the cable does not a molded sleeve, to prevent electrical become excessively bent or twisted, leakage, electrical shock, fire, injury or... -
Page 8: Before Starting
3 Start the pump and check the quantity If the pump is connected to a piping system, the direction of rotation can be checked as of water or the discharge pressure. follows: 4 Stop the pump. 1 Start the pump and check the quantity 5 Compare the results taken under point of water or the discharge pressure. - Page 9 Countermeasure: If the operating current OPERATION exceeds the rated value, pump motor overload may be a cause, or there may be insufficient WARNING: back pressure. Make sure the pump has been installed under proper conditions as described • Do not operate the pump in dry pit, in Installation (page 5).
-
Page 10: Operating Water Level
and restarting will result in damage to the OPERATING WATER LEVEL pump. Do not continue operation at a very low lift, low water level, or while the strainer stand CAUTION: is clogged with debris. Not only will performance suffer, but such conditions may •... - Page 11 1 Washing the Pump: Remove surface should be repaired by cleaning accumulated matter from the surface up that area, drying it and then of the pump and wash it with clean applying touchup coating. water. Take special care to remove any NOTE: touchup is not supplied.
-
Page 12: Troubleshooting
case the pump will need to be dismantled STORAGE and repaired. When the pump is out of use for an extended • Replacing the Oil period, wash it and dry it thoroughly, then store Remove the Oil Plug and drain all the oil, it indoors. - Page 13 TROUBLESHOOTING Trouble Cause Remedy Operates, but stops after a while. 1. Prolonged dry operation has 1. Raise stop water level activated motor protector and 2. Lower liquid temperature caused the pump to stop 2. High liquid temperature has activated motor protector and caused the pump to stop.
-
Page 14: Warranty Conditions
WARRANTY CONDITIONS GENERAL PUMP COMPANY warrants to the original service/warranty has been in contact or user that its products are free from defects in used with hazardous liquids. materials and workmanship at the time of shipment 8. goods are maintained and serviced and will make good, by repair or at its option by according to instructions set by GENERAL replacement, faults and/or defects which appear... - Page 15 WARRANTY CONDITIONS hazardous liquids, electrolytic action, liqiud This warranty does not exclude any condition or temperature beyond the recommended warranty implied by the Trade Practices Act or range, cavitation, improper supply voltage, or seperate state laws and is in additon to any right insufficient liquid to enable the pump to that the original purchaser or any subsequent perform to specification.
Need help?
Do you have a question about the UMDZ7500/80/30 and is the answer not in the manual?
Questions and answers