Related Manuals for Bison Garfield GCA1250HC
Summary of Contents for Bison Garfield GCA1250HC
- Page 1 伀 倀 䔀 刀 䄀 吀 伀 刀 ᤠ 匀 䴀 䄀 一 唀 䄀 䰀 䌀 愀 爀 爀 礀 ⴀ 䄀 氀 氀 䔀 樀 攀 挀 琀 椀 漀 渀 匀 挀 爀 愀 瀀 攀 爀 倀...
- Page 2 1250 CARRY ALL Operator's Manual 12.5 YD. CU., DOLLY...
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION IMPORTANT SAFETY INFORMATION BE AWARE OF SIGNAL WORDS PREPARE FOR EMERGENCIES SHUTDOWN AND STORAGE ASSEMBLY AND SET-UP PARTS MANUAL 1250 HYDRAULIC SYSTEM DRAWBAR HOOK-UP OPERATION SETTING THE VALVES BLADES WARRANTY... -
Page 4: Introduction
INTRODUCTION Welcome! You are now the owner of one of the most versatile machines for landscaping, terracing and earth moving. In years to come, your farm or ranch operation will benefit from the efficiency, utility, and economy provided by the GARFIELD SCRAPER. This CA1250 model has been designed with the most modern methods and built by skilled workers using quality materials. -
Page 5: Important Safety Information
IMPORTANT SAFETY INFORMATION Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them. Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment. -
Page 6: Prepare For Emergencies
PREPARE FOR EMERGENCIES Be prepared if a fire starts. Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctor, ambulance, hospital and fire department near phone. SHUTDOWN AND STORAGE Lower machine to ground, put tractor in park, turn off engine, and remove the key. Detach and store implements in an area where children normally do not play. - Page 7 MAIN FRAME ASSEMBLY ITEM PART # DESCRIPTION QTY. GBCA12040100W CA1250 MAIN FRAME, ASSEMBLY GBCA12040600W RIGHT SPOILER GBCA12040700W LEFT SPOILER GBCA12050009C SIDE TUBE GBCA12051000W CYLINDER PIN ASSY SP4110-4050-01 3" X 36" X 1-1/2" STROKE HYD CYL (HCY3X36X112) SP4110-4094-01 4" X 12" X 2" STROKE HYD CYL (HCY4X12X2) SP4110-4098-01 4"...
- Page 8 DOLLY ASSEMBLY ITEM PART # DESCRIPTION QTY. GBCA12040500W DOLLY ASSEMBLY GBCA12040001C LARGE 2" HOLE PULL BLOCK GBCA12051100W HITCH PIN GBCA12050007C FRONT SPINDLE GBCA12011300W HOSES SUPPORT GBCA12051400W PULL BLOCK LOCK SP4190-0015-25 W871 HUB W/CUPS AND STUDS/COMPLETE (WHBW871) SP4190-1080-00 10" TUBE MT JACK 5000# (JK105) SP4330-2540-01 H46 X 18-20 TIRE AND WHEEL (TIRE18) SP4220-1022-26...
- Page 9 LIFT GATE ASSEMBLY ITEM PART # DESCRIPTION QTY. GBCA12050400W LIFT GATE ASSEMBLY GBCA12050900W PIVOT PIN ASSY GBCA12051000W CYLINDER PIN ASSY PUSH GATE ASSEMBLY ITEM PART # DESCRIPTION QTY. GBCA12040300W PUSH GATE ASSEMBLY GBCA12011200W ROLLER W/PIN GBCA12010005C ROLLER GBCA12010006C SIDE ROLLER GBCA12010901C 4"...
- Page 10 REAR END FRAME ASSEMBLY ITEM PART # DESCRIPTION QTY. GBCA12040200W REAR END FRAME, ASSEMBLY GBCA12050600W SPINDLE, ASSEMBLY (WSPQ900S) GBCA12051200W PIN FOR HINGE GBCA12010800W 6-1/2" LONG PIN GBCA12010004C 1/2" WASHER GBCA12010011C DUST CAP (WDCQ900S) GBCA12050005C CLAMP SP4330-2090-01 20 X 20 FOR 12 YD CA (TIRE 20X20) SP4380-1025-05 S900 HUB FOR REAR 12 YD CA (WHBQ900S) SP4150-7985-00...
-
Page 11: 1250 Hydraulic System
1250 HYDRAULIC SYSTEM... - Page 12 1250 HYDRAULIC SYSTEM GCA1250 ITEM PART # DESCRIPTION SP4110-3050-01 3/4” HYD. RELIEF VALVE (HV34) 1.00 SP4110-4050-01 3" X 36" X 1-1/2" STROKE HYD. CYL (HCY3X36X112) 2.00 SP4110-4094-01 4” X 12” X 2" STROKE HYD CYL (HCY4X12X2) 2.00 SP4110-4098-01 4" X 16" X 2" STROKE HYD. CYL (HCY4X16X2) 2.00 SP4110-6012-00 PIONEER END W/POPPET 1/2"(HEPP) 4.00...
-
Page 13: Drawbar Hook-Up
DRAWBAR HOOK-UP FIXING BOLT Keep the pull block on horizontal position tightening the fixing bolt. Be sure to loosen the bolt before operating. There are twenty-two different grease zerks on the machine; one on each cylinder pin; one on each of the rear frame pivot pins; eight on the push gate; one on the ball and receiver; and one on the swivel hitch. -
Page 14: Operation
OPERATION The 1250 Carry All scrapers are designed with Category III and IV hitch. Horsepower rating of tractor should be between 200 and 300 hp for the 1250 single and between 250 and 350 hp for the 1250 tandem. IMPORTANT: You could lose steering control if your tractor is too light. Refer to your tractor's manual to determine if additional ballast is needed. -
Page 15: Blades
Remove acorn nut, loosen lock nut and turn adjustment screw counter-clockwise to increase speed of the pushgate. BLADES Inspect cutting edges daily. Replace cutting edges when center blade has been worn to approximately 4” and side edges worn to approximately 3”. CENTER BLADE RIGHT SIDE BLADE CAUTION... -
Page 16: Warranty
WARRANTY Under the conditions described herein GARFIELD, INC. will within 12 months from the date of purchase on agricultural designed the operated machinery, and 90 days for hire commercial machinery, supply or at GARFIELD’s option, repair any part manufactured and/or workmanship, upon receipt of the damaged part. - Page 17 FORWARD This manual is written as a guide for owners and operators of the GARFIELD equipment, read it carefully and follow the suggestions which are made. Keep this manual in a convenient place for quick, easy reference and use it whenever questions come up. Fill in the following warranty registration form and return to GARFIELD INC.