Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Eastwood 31639
- Page 1 Item #31639 ELECTRONIC WHEEL BALANCER INSTRUCTIONS...
-
Page 2: Specifications
The EASTWOOD ELECTRONIC WHEEL BALANCER brings the convenience and economy of a professional, high precision tire and wheel Balancer to the well-equipped DIY or race shop. Allows quick balancing and guidance for applying clip-on or stick-on weights to a variety of wheel types, sizes and materials. -
Page 3: Safety Information
Damaged or entangled cords increase the risk of electric shock. e) When operating electrical equipment outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. To order parts and supplies: 800.343.9353 >> eastwood.com... - Page 4 5) SERVICE a) Have your electrical equipment serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the electrical equipment is maintained. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
-
Page 5: Installation Location
• There MUST be a minimum of 4 ft. of open space surrounding the Balancer. • The Balancer MUST be firmly attached to the floor with suitable concrete anchors or similar hardware (not included). To order parts and supplies: 800.343.9353 >> eastwood.com... - Page 6 Tubular Steel Guard Frame [B] over the Guard Mounting Shaft at the rear of the Main Balancer Unit [T]. Fasten with the M10 x 45mm Bolt [F] & Nut [G] (FIG 3). FIG. 2 FIG. 3 Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 7 ACCESSORY STORAGE POST INSTALLATION • Thread the three Accessory Storage Posts [L] with Protective Rings [M] into the threaded holes on the left side of the Main Balancer Unit Cabinet [T] (FIG 5). FIG. 5 To order parts and supplies: 800.343.9353 >> eastwood.com...
-
Page 8: Function Key Combinations
NOTE: The following combinations are listed in this location for quick reference only. They are described in much greater detail further along in these instructions. STOP = Guard Switch function setting a – = Toggle between ounce or gram settings STOP = Begin sequence for changing Balancer Settings = Balancer calibration FINE = Balancer function checks Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com... -
Page 9: Operation
Wheels and tires MUST be clean and free of all mud, grit or other debris as they will cause an inaccurate balance reading. All tire pressures MUST be set to specific vehicle or tire manufactures specifications or inaccurate balance readings will result. To order parts and supplies: 800.343.9353 >> eastwood.com... - Page 10 Quick-Release Ears in a Clockwise direction while sliding onto threaded shaft (FIG 8). Apply moderate hand pressure to keep the wheel/tire from spinning while tightening the Hub Wing Lock. FIG. 7 FIG. 8 Rotate Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 11 • Enter Wheel Rim Diameter – Using the included Wheel Width/Diameter Caliper [S], observe and record the Diam- eter dimension which is Value “d”. Press “d-“ or “d+” Keys to enter Value “d”. FIG. 11 To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 12 12:00 position on the rim (FIG 13). • Lower Guard and once again press “START” Key to begin Spin Cycle. • After Balancer stops, the Imbalance Condition LED’s will display “0” and the balancing is complete. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 13 Wheels and tires MUST be clean and free of all mud, grit or other debris as they will cause an inaccurate balance reading. All tire pressures MUST be set to specific vehicle or tire manufactures specifications or inaccurate balance readings will result. To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 14 Wheels and tires MUST be clean and free of all mud, grit or other debris as they will cause an inaccurate balance reading. All tire pressures MUST be set to specific vehicle or tire manufactures specifications or inaccurate balance readings will result. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 15 Note that “ON” denotes the Guard Closed, Automatic Start Function is activated (FIG 21). • To toggle between “On” and “Off”, press “b+” or “b-” Keys. Press “a+” Key to save chosen setting and progress to next setting. FIG. 21 To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 16 If desired, it may be switched to MM. Increase or decrease brightness: • Press “a+” Key to enter the setting (FIG 25). • To toggle between “Inch” and ”MM”, press “b+” or “b-” Keys. Press “a+” Key to save chosen setting and exit settings sequence. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 17 Wheels and tires MUST be clean and free of all mud, grit or other debris as they will cause an inaccurate balance reading. All tire pressures MUST be set to specific vehicle or tire manufactures specifications or inaccurate balance readings will result. To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 18 3 PIEZOELECTRIC SENSOR CHECK – To verify operation of Piezoelectric Sensor and internal circuits. • Press “ALU” Key. • Gently apply a sideways or downward pressure on the Main shaft. Numeric values should change on the LED Displays (Control Panel Display #’s 1 & 2). Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
-
Page 19: Maintenance
10mm Flat Wrench [K], push motor rearward while tightening mounting bolts. – Re-check tension and re-adjust if necessary (FIG 31). – Replace cover and Wheel Measurement Scale. """" FIG. 31 8mm Motor Bolts Slots Deflect Belt 1/8” To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 20: Troubleshooting
Tighten wheel on Main shaft. Main Shaft Cycle or When STOP Key is Belt Drive slipping Tighten Drive Belt per Maintenance instructions Pressed Accuracy of Balancer is Balancer out of calibration Follow Calibration Instructions Diminished or in Question Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com... - Page 21 1-800-343-9353 Re-perform Calibration Procedure using 100 Gram. RED Calibration Weight not only supplied 100 Gram, RED Calibration properly used Weight ERR 8 Calibration Procedure failure Contact Eastwood Tech @ Internal fault 1-800-343-9353 To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 22 NOTES Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 23 NOTES To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 24 If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: techelp@eastwood.com PDF version of this manual is available online >> eastwood.com/31639manual The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA US and Canada: 800.343.9353...
Need help?
Do you have a question about the 31639 and is the answer not in the manual?
Questions and answers