Table of Contents
Advertisement
– Risk of electric shock!
Cleaning and care
Cleaning and care
Pull out the mains plug!
– Risk of explosion! No solvents!
Clean machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use abrasive detergents.
1. Open and remove the maintenance cover.
– Immediately remove washing and cleaning agent residue.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
2. Carefully unscrew the pump cover - do not remove it completely.
... if it contains detergent or fabric softener residue.
1. Pull out, depress the insert and remove the drawer completely.
3. Let the water drain into a shallow container (let the remainder drip
4. Remove the pump cover. Remove foreign material/fluff from inside the
2. Remove insert: Press the insert upwards with your finger.
3. Clean the detergent dispenser and the insert with water and a brush.
4. Refit the insert and secure in place.
5. Clean the interior, pump cover thread and pump housing
5. Insert the detergent drawer.
Leave the detergent drawer open so that residual water can evaporate.
6. Refit the pump cover and screw on tightly.
Drum
Leave the washing machine door open so that the drum can dry.
7. Insert the maintenance cover and close it.
Rust stains – use chlorine–free cleaning agent, not steel wool.
Descaling
No laundry in the machine!
This should be not be necessary if the detergent is dispensed correctly. However, follow
the instructions of the descaler manufacturer .
Frost protection
If the washing machine is located in a room which is exposed to freezing temperatures, any
residual water in both the pump and the water inlet hose must be drained every time after the
machine is used.
1. Turn off the tap.
– Draining the pump
Page 9 Detergent solution pump
2. Select any programme (except Single Spin).
– Draining the water inlet hose:
3. Select Start/Soak. Leave programme running for approx. 40 seconds.
1. Turn the tap off.
4. Set the programme selector to Off. Pull out the mains plug.
2. Unscrew the hose from the tap and hold the end of the hose over a container.
3. Select any washing programme.
4. Select Start/Soak.Leave programme for approx. 40 seconds.
1. Remove the hose from the tap.
Water left inside the inlet hose will be drained out.
5. Screw the hose back onto the tap.
2. Reconnect the hose and check for leaks.
8
7
– Risk of scalding! Allow detergent
Consumption values
solution to cool down!
– Turn off the tap!
Variants
Detergent solution pump
1
– Set the programme selector to Off, pull out the mains plug .
Energy efficiency grade
Electricity consumption
2
Water consumption
Rate of washing ability
Noise value
Spining noise value
Washing noise value
onto a floor cloth). Repeat the operation until there's no water left.
Energy consumption tested under standard programme Super Clean with additional option
Intensive according to GB standard.
pump.
2
1
(fan impeller in the detergent solution pump must be able to rotate).
Technical specifications
To prevent unused detergent from flowing into the outlet during the next
wash: pour 1 litre of water into dispenser II and start the Single Spin
programme.
Filter in the water inlet hose
Reduce the water pressure in the supply hose:
Customer service
Before calling the customer service, please check whether you can eliminate the fault yourself
Clean the filter:
page 11 What to do if...
If yor require advice, even during the warranty period, you will incur the costs for the call-out
Clean the filter with a small brush.
of a technician.
When calling customer service, please give the detailed of your address, telephone number,
fault description, purchase date, product number (E-Nr.) and the production number (FD) of
or
the appliance to prevent unnecessary call-outs. This will save your additional costs.
Remove the hose from the rear of the appliance.
Remove filter with pliers and clean.
E-Nr .
Universal customer service number in China: 4008899999
9
Free consultation hotline: 8008289828
What to do if ...
WM08X0R00W
Water is running out.
2
Water not flowing in.
0.60
Detergent not washed in.
45
1.03
Washing machine door cannot be
opened.
Programme does not start.
68dB(A)
54dB(A)
Detergent solution is not drained.
Additional function could not
activate for selected programme.
Water not visible in the drum.
Spin cycle actuated several times. – Not a fault - unbalanced load detection system adjusts
Detergent in chamber I is not
washed away.
WM series: a = 600 mm
Detergent residue in the detergent
b =560 mm
dispenser
c = 850 mm
WS series: a = 600 mm
Foam is coming out of the
detergent drawer.
c
b = 400 mm
c = 850 mm
net weight: 60 kg
Excessive noise, vibrations and
"wandering" during spin cycle.
Display panel/indicator lights do
b
a
not function while the appliance is
running.
Programme sequence longer than
usual
Detergent residues on the laundry – Occasionally, phosphate-free detergents contain water-
Washing result not satisfactory
If you cannot correct a fault yourself or a repair is required:
– Set the programme selector to off and pull the mains plug out of the socket.
These numbers are shown on the rating
– Turn off the tap and call the customer services.
plate which can be found on the frame of
FD
the open door and also on the rear of the
appliance.
10
– Fit/refit drainage hose.
– Tighten screw–fitting on the supply hose.
– Start/Soak not selected?
– Tap not open?
– Filter blocked? Clean filter
Page 9.
– Water inlet hose kinked or jammed?
– Safety function active. Programme stopped?
– Water in drum? Select Single Spin programme.
– Please read the
operating instructions
– Start/Soak selected?
and installation
– Washing machine door not closed properly?
instructions supplied
before switching on
– Clean detergent solution pump
Page 9.
– Clean outlet pipe and/or drainage hose.
the washing machine.
– Can the additional function be selected?
Page 7,
programme overview.
– Not a fault - water below the visible area.
– Any failure and losses
caused by ignoring
imbalance.
the above mentioned
– Prewash programme not selected?
items, including
cautions in the
instructions, are not
– Detergent is damp or lumpy, clean the detergent
covered by our
dispenser
Page 8.
warranty and liability.
– Use the dosing aid for liquid detergent.
– Please keep all
documents in a safe
– Too much detergent used?
place for further
Mix 1 tablespoon of fabric conditioner with ½ litre of
reference. In cases of
water and pour into dispenser II in the detergent drawer.
doubt, please contact
– Reduce detergent dosage for the next wash cycle.
customer service.
– Follow the safety
– Appliance feet fixed?
instructions on
Secure appliance feet
Installation instructions.
Page 8.
– Transportation bolt removed?
– Contents of this
Remove transportation bolt
Installation instructions.
instruction could be
– Power failure?
changed without
– Circuit breaker tripped? Reset the circuit breaker/
written notice.
change the fuse.
– If the fault occurs repeatedly, contact customer service.
– Not a fault-unbalanced load detection system is
adjusting the imbalance by repeatedly distributing the
laundry .
– Not a fault-foam detection sysytem active.
Operating instructions
insoluble residues.
– Select Single Rinse or blush the laundry after washing.
XQG60-WM08X0R00W
– Soiling is greater than expected? Select a suitable
programme and select option Intensive.
– Detergent is underdosed?
11
en
Advertisement
Table of Contents
