Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Philio Manuals
  4. Control Unit
  5. PAN07-1C
  6. Manual

Philio PAN07-1C Manual

Two spdt switch module with meter
Hide thumbs

Advertisement

Quick Links

Download this manual
Enlarged version
PAN07-1C/-2C/-3C
PAN09-1C/-2C/-3C
TWO SPDT Switch module with meter
Fig 1. PAN07 Assembling
Fig 2. PAN09 Assembling
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the PAN07-1C and is the answer not in the manual?

Questions and answers

Related Manuals for Philio PAN07-1C

Summary of Contents for Philio PAN07-1C

  • Page 1 PAN07-1C/-2C/-3C PAN09-1C/-2C/-3C TWO SPDT Switch module with meter Fig 1. PAN07 Assembling Fig 2. PAN09 Assembling...
  • Page 2 pressing the On/Off button on the Switch. This in-wall dual relay switch module is a transceiver which is a Z-Wave Plus enabled device and is fully compatible with any Z-Wave enabled network. Mini The table below lists an operation summary of basic Z-Wave functions. Please size design let the module can easily hide itself into the wall box and that will be refer to the instructions for your Z-Wave Certificated Primary Controller to...

  • Page 3: Choosing A Suitable Location

    1. The PAN11 is an always listening flashes on and off alternately at 0.2 second intervals. Overload Association one press one flash LED Z-Wave device, so associations state can be cleared by disconnect and reconnect the Switch to the be added or removed by a controller main power at any time.
  • Page 4 3. To manually turn ON the Switch, press and release the On/Off button. The Report ON:[Command Class Switch Binary, Switch Binary Report, Value LED will light ON for 1 second, and the load plugged into the Switch will = 255(0xFF)] also turn ON.
  • Page 5 The content of Alarm Report For group 2, the Switch will report (1) ON/OFF status of Relay1 (2) Instant Alarm report command: [Command_Class_Alarm, Alarm_Report, Alarm Type = [Command_Class_Alarm, Alarm_Report, Alarm Type = [Command_Class_Alarm, Alarm_Report, Alarm Type = [Command_Class_Alarm, Alarm_Report, Alarm Type = Power Consumption (Watt) of Relay1 (3) Accumulated Power Consumption 0x08, Alarm Level = 0xFF] 0x08, Alarm Level = 0xFF]...
  • Page 6 Meter Report Command: Example: Scale = 0x04 (V) [Command Class Meter，Meter Report，Rate Type = 0x01， Meter Type Precision = 1 =0x01， Precision = 2，Scale = 0x00，Size = 4，Meter Value (KWh)] Size = 2 (2 Bytes of V) Meter Value 1 = 0x09(V) Example: Meter Value 2 = 0x01(V) Scale = 0x00 (KWh)
  • Page 7 [Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type = Source End Point = 0x05 (this is the endpoint of command owner 0x01， Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter Value(PF)] here we assume endpoint is 5，if the Example: owner doesn’t support multi Scale = 0x06 (PF) Channel this value will be 0) Precision = 2...
  • Page 8 0x25) Command =0x03 (Switch_Binary_Reportet = 0x3) (ON=0xFF ， OFF=0x00) Parameter 1 = 0xFF Command =0x01 (Switch_Binary_Set = 0x01) Note: If the Multi-Channel Encapsulated BASIC_GET/SWITCH_GET command follow a switch On/Off command, it should add 0.5s time delay before the Get command. (ON=0xFF ，...
  • Page 9 this value will be 0) (Bit Address+Destination End Point = 0x01) (Bit Address =0；Destination End Point Below is the example show PAN07/PAN09 report to last command range1~3) COMMAND_CLASS_MULTI_CHANNEL Command Class = 0x32 ( Command_Class_Meter_V3 = 0x32) MULTI_CHANNEL_CMD_ENCAP Command =0x05 ( Meter_Reset = 0x05) Source End Point = 0x03 2-3-5 METER_GET：...
  • Page 10 2-3-5-2 Get Instant Power Consumption (Watt) from endpoint Parameter 1 = 0x00 (Scale = KWH = 0x00) METER_GET example： COMMAND_CLASS_MULTI_CHANNEL Accumulated power consumption (KWH) Report example： MULTI_CHANNEL_CMD_ENCAP COMMAND_CLASS_MULTI_CHANNEL Source End Point = 0x05 (this is the endpoint of command owner, MULTI_CHANNEL_CMD_ENCAP here we assume endpoint is 5，if the owner Source End Point = 0x03...
  • Page 11 doesn’t support multi Channel this value (Bit Address+Destination End Point = 0x05) (Bit Address =0；Destination End Point = will be 0) command owner Endpoint value) (Bit Address =0；Destination End Point (Bit Address+Destination End Point = Command Class = 0x32 (Command_Class_Meter_V3 = 0x32) 0x03) range1~3) Command =0x02...
  • Page 12 PAN07/PAN09 AC load current (I) example： (Precision = 1，Scale Bit1Bit0 = 0x00， Parameter 2 = 0x22 Size = 2) COMMAND_CLASS_MULTI_CHANNEL Parameter 3 = 0x09 Voltage = 0x0910 = 232.0V MULTI_CHANNEL_CMD_ENCAP Source End Point = 0x03 (Meter report = Endpoint3) Parameter 4 = 0x10 (Bit Address+Destination End Point = 0x05) (Bit Address =0；Destination End Point = 2-3-5-4 Get load current I from endpoint command owner Endpoint value)
  • Page 13 Source End Point = 0x05 (this is the endpoint of command owner, Command =0x02 (Meter_Report = 0x02) here we assume endpoint is 5，if the owner (Scale Bit2 = 1 ，Rate Type = 0x01， Parameter 1 = 0xA1 does not support multi Channel this value Meter Type=0x01) will be 0) (Precision = 2，Scale Bit1Bit0 = 0x10，Size...
  • Page 14 of KWH for Load Set command Relay state Caution Relay 1 : Control relay Basic_Set or Binary_Switch_Set ON Relay1 & control refer to meter Relay2 ON mode wattage Basic_Set or Binary_Switch_Set OFF Relay1 & 2 : Control relay directly Relay2 OFF Restore 0 : All relay stay Relay state...
  • Page 15 3-4 Edge and Pulse mode This is a warning when the KWh of load over the preset threshold value, If the setting value is 10000, when the Accumulated Power Consumption of Relay1 or Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle Relay2 over this value, PAN07/PAN09 will send KWh Meter Report command to mode, default value is Edge mode.

  • Page 16: Troubleshooting

    * COMMAND_CLASS_ALARM Command Class will be disabled. The default value is 1. * COMMAND_CLASS_SCENE_ACTIVATION * COMMAND_CLASS_SCENE_ACTUATOR_CONF Protection Command Classes * COMMAND_CLASS_PROTECTION * COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 PAN07/ PAN09 supports Protection Command Class version 2, it can protect * COMMAND_CLASS_MULTI_CHANNEL_V3 the switch against unintentionally control by e.g. a child. And it can also protect * COMMAND_CLASS_METER_V3 * COMMAND_CLASS_CONFIGURATION the switch from being turned off by setting it in “No RF Control”...

  • Page 17: Fcc Interference Statement

    They can take this product for environmental safe recycling. (1) This device may not cause harmful interference, and Company of License Holder：Philio Technology Corporation (2) This device must accept any interference received, including interference that may Address of License Holder：8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist., cause undesired operation.

This manual is also suitable for:

Pan07-2cPan07-3cPan09-1cPan09-2cPan09-3cPan07