Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toolex 597076
Summary of Contents for Toolex 597076
- Page 1 1 / 16 1...
-
Page 2: Safety Warnings And Precautions
SAFETY WARNINGS AND SAVE THIS MANUAL PRECAUTIONS Keep this manual for the safety WARNING: When using tool, basic safety warnings precautions, assembly, precautions should always be followed to operating, inspection, maintenance and reduce the risk of personal injury and cleaning procedures. Write the product’s damage to equipment. - Page 3 Electrical Safety Damaged Power Cords increase the 1. Grounded tools must be plugged risk of electric shock. into an outlet properly installed and 6. When operating power tool grounded in accordance with all outside, sue an outdoor extension codes ordinances. Never cord marker “W-A”...
-
Page 4: Specific Safety Rules
If unreadable or missing, Such preventive safety measures contact TOOLEX INDUSTRIAL for a reduce the risk of starting the tool replacement. accidentally. 2. Always wear the approved safety 5. Store idle tools out of reach of... - Page 5 4. Avoid unintentional starting. Make location well away from sure you are prepared to begin work combustible; protect before turning on the tool. combustibles with a cover made of 5. Never leave the tool unattended fire resistant material. when it is plugged into an electrical b.
- Page 6 atmospheres containing h. Dangerously reactive Use enough ventilation or exhaust, or flammable gases, vapors, liquids, both, to keep fumes and gases from and dust. your breathing zone and general area. Provide adequate ventilation in ℓ Where ventilation is questionable, work areas prevent have a qualified technician take...
- Page 7 Manual for the material you will weld or cut. Proper cylinder care. Secure cylinders to a cart, wall, or post, to prevent them from falling. All cylinders should be used and stored in an upright position. Never drop or strike a cylinder.
-
Page 8: Specifications
SPECIFICATIONS Model ANVAN TIG 200 Parameters Rated Input Voltage (V) 1PH ~ 220V±15% ( 50/60HZ) Rated Input Power (KVA) Rated Input Current (A) Related output 200A/18 V Output Current Range (A) 10 ~ 200 35% 200A Duty Cycle 60% 153A 100% 118A No Load Voltage (V) Efficiency (%) - Page 9 metal slag onto the floor, and it will Duty Cycle scatter for 8-10 feet or more in any Duty Cycle equipment direction. Have an adequate fire specifications which defines the number of extinguisher available if needed. minutes within a 10 minute period that a ASSEMBLY piece of equipment can safely operate.
- Page 10 Front Panel TIG Torch Connector and Instruction Gas outlet (2) Ground socket (4) TIG torch control socket Cable (1) socket (3) 1. TIG torch cable socket: Connect TIG torch control (1B) of the TIG torch The front panel of MAX TIG 160 and MAX left to this socket.
-
Page 11: Operation
a. Unscrew the Ceramic Nozzle (6A) “ ” means MMA welding, on the Torch Handle (4A). when you chose this welding mode, b. Unscrew the Collect Housing (5A). please plug the welding plug with c. Place a 5/32” prepared tungsten cable to the TIG control socket (refer welding rod (not included) into the to page 9, (1)). - Page 12 the arc. Do not strike like a match. Never tap the electrode wire to ignite the arc; it will damage the electrode. 14. When ignites, tilt electrode forward and hold it near the workpiece. 15. If too much current is drawn from the welder;...
- Page 13 electrical outlet. welding and gas metal arc welding, allowing for stronger, higher quality welds. Tungsten Inert Gas (TIG) Welding However, GTAW is comparatively more complex and difficult to master, and Gas tungsten arc welding (GTAW), furthermore, it is significantly slower than also known as tungsten inert gas (TIG) most other welding techniques.
- Page 14 4. STAINLESS STEEL（SUS304）WELDING PARAMETER: Steel Tungsten Wire Welding Clearance Argon flux Clearance thickness diameter diameter current size form (mm) (mm) (mm) (L/min) (mm) 1.0～1.6 0～1.0 15～30 4～5 a、b 1.0～1.6 0～1.6 25～30 4～7 a、b 1.0～1.6 0～1.6 50～70 6～9 1.6～2.4 1.6～2.4 65～95 6～9 1.6～2.4 1.6～2.4...
-
Page 15: Maintenance
CLEARANCE FORM attempt any electronic repairs. Any MAINTENANCE repairs must be completed by a WARNING! Make sure Power qualified technician. Opening the tool Switch of the welder is in its “OFF” will void any warranties, and may position and that the tool is unplugged result in damage to equipment or from electrical... - Page 16 TROUBLESHOOTING IMPORTANT! Be CERTAIN to shut off the Welder and disconnect it from power and air before adjusting, cleaning, or repairing the unit. A technician should discharge all capacitors before performing and internal procedures. Problem Possible Causes Likely Solutions Tool will not start 1.
Need help?
Do you have a question about the 597076 and is the answer not in the manual?
Questions and answers