Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HiWeigh PT2
Summary of Contents for HiWeigh PT2
- Page 1 SPECIAL PRINTER...
-
Page 3: Table Of Contents
Content Precautions ..............................3 Chapter 1 Product introduce ........................7 1.1 Printer exterior ............................ 7 1.2 Accessory ............................7 1.2.1 Standard accessories ........................7 1.2.2 Options accessories ........................8 Chapter2 Function characters ........................8 2.1 Specifications ............................. 8 2.2 Other specifications ..........................9 Chapter 3 Using method ...........................10 3.1 Prepare before using .........................10 3.1.1 Li-ion battery installation ......................10... -
Page 4: Precautions
Precautions ◆ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. - Page 5 ◆ Operation Precautions Be sure not to print continuously over 1meter, otherwise may cause damage to the printer head.
- Page 6 Water or other liquid should not spill into the printer, also the printer should not be appeared in the rain, or else may cause printer damage. Please do not open the paper case cover when printing; otherwise the printer may work improperly. If print with serial interface, should not unplug the interface cable in the course of printing, or else some printing data may be lost.
- Page 7 performance, and reduced product life. 1) Risk of explosion if battery is replaced by an incorrect type. 2) Dispose of used batteries according to the instructions. 3) Do not allow water, sea water from entering or leaking into the battery inside. If the batteries internal safety device burn, when changing it, it may produce any abnormal current and/or voltage, and cause any abnormal chemical reaction, then may cause the battery overheating, fire and/or explosion.
-
Page 8: Chapter 1 Product Introduce
Chapter 1 Product introduce 1.1 Printer exterior 1. Feed paper key 2. State indicator light 3. RS232 serial port socket 4. Infared ray(IR) interface 5. Printer upper cover 6. Power key 7. Power Charging indicator light 8. Power port 9. Mini USB port 10. -
Page 9: Options Accessories
USB Interface Cable Battery Power Adapter Paper Roll User Manual 1.2.2 Options accessories cigarette lighter Serial Interface Cable Protective Case jack charger Chapter2 Function characters 2.1 Specifications Model PTP-II/IR PTP-II/BT PTP-II/WIFI(Developing) Printing method Line thermal printer Printing speed 50~80mm/s... -
Page 10: Other Specifications
Dot pitch 8dots/mm, 384 dots/line Printing width 48mm Paper width 57.5±0.5mm Paper roll outer 40mm (Max.) diameter Paper roll inner 13mm(Min.) diameter Paper thickness 60-80um Overall 79x110x45mm dimension(WxDxH): Weight ( g) 210(non- including the paper roll) Printing characters ANK: 8x16,9X17, 9x24,12x24 GBK:24x24 Characters/line ANK:48, 42, 32 GBK:24, 16... -
Page 11: Chapter 3 Using Method
Power supply: 2000mAh rechargeable Li-ion battery Power alarm: indicator flashes when printer will run out of power and give out two short hoots. When running out of power, it will give out interval hoot to indicate charging. Battery full charge time: 2 to 4 hours. -
Page 12: Basic Function Using
Rubber Roller Top cover Use two fingers to press this place and open the top cover Thermal paper roller Operation methods: 1) Use two fingers to press the place showed in the above picture and open the top cover. 2) Put the paper roll into the paper case, pay attention to the direction of paper. If loaded reversely, it won’t print. -
Page 13: Paper Feeding
Inspect method: turn-off. Hold [FEED] button, and then press [POWER] button the printer will print out the inspect page, the inspect page including the current state, setting, example of printer. 3.2.4 Paper feeding Under the usual working state, press [FEED] button, start to feed paper, and will stop till 250mm. If the paper has dark mark approved by this printer, when print to the dark mark, the printer will stop feed paper. -
Page 14: Bluetooth
When PTP-II/IR communicates with the host devices that hardware also meets the regulation of IrDA 1.1 physical layer, make the IR interfaces ( from both PTP-II and the host device ) right towards to each other ( angle shall not be more than 30° ), without any obstacles between them, the distance shall be less than 0.5M. -
Page 15: Matched Pair
Using method: 1. Through the Bluetooth tray (or on the control board), right click the Bluetooth logo, choose” Add Bluetooth equipment 2. after some time, to show find out the new equipment “PTP-II” 3. Choose “next step”, input the password”0000” in the third option” input the password” till to the finished 4. -
Page 16: Led Indicator And Buzzer Definition
succeeds in pairing. After finished pairing, other the host device (upper machine) still can pair with this mobile thermal printer. One printer can be most allowed to pair with 8 units upper machines (the host devices) . If the ninth device will be paired with the printer, the earliest ones will be deleted from printer paring list automatically. -
Page 17: Auto Dormancy/Automatic Awaken, Automatic Turnoff
Reflection rate to IR：<10% （reflection rate to the black mark on paper >65% ） Hps：Hps indicates the distance from down edge of detecting mark from beginning line. 0mm≤Hps≤1mm 4.3 Auto dormancy/automatic awaken, automatic turnoff In order to save energy, prolong the using time, PTP-II printer adopts the advanced automatic dormancy, automatic awaken technology. - Page 19 User Manual v.201811...
Need help?
Do you have a question about the PT2 and is the answer not in the manual?
Questions and answers