HiWeigh POS58 User Manual
  1. Manuals
  2. Brands
  3. HiWeigh Manuals
  4. Printer
  5. POS58
  6. User manual

HiWeigh POS58 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

P58
Thermal Printer POS58 -

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POS58 and is the answer not in the manual?

Questions and answers

Related Manuals for HiWeigh POS58

Summary of Contents for HiWeigh POS58

  • Page 1 Thermal Printer POS58 -...
  • Page 3 POS-58 Receipt Printer User Manual All specifications are subjected to change without notice...

  • Page 4: Table Of Contents

    - 1 - POS-58 User Manual 1 INTRODUCTION........................- 2 - 1.1 POS-58 Receipt Printer...................... - 2 - 1.2 Feature..........................- 2 - 1.3 Outline..........................- 2 - 1.4 Caution..........................- 2 - 2 SETTING UP THE PRINTER...................... - 3 - 2.1 Unpacking.........................

  • Page 5: Pos-58 User Manual

    - 2 - POS-58 User Manual Notice Notice Notice Notice： This manual has been prepared for various models with same body that have built at Our Company. So some content of this manual may not use on your device. 1 1 1 1 INTRODUCTION INTRODUCTION INTRODUCTION INTRODUCTION...

  • Page 6: Unpacking

    - 3 - POS-58 User Manual “OFF”, before you connect or remove the cables on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF”.

  • Page 7: Rs232 Interface

    - 4 - POS-58 User Manual the back of the printer: Commucation cable Cash drawer cable Power supply connector Note: Before connecting any of the cable, make sure that both the printer and the host are turned off. 2.3.1 RS232 INTERFACE POS-58S use RS232 intreface to connect the printer and host computer.

  • Page 8: Usb Interface

    - 5 - POS-58 User Manual Parallel pin definition: SIGNAL DEFINITION Latch strobe pulse. The printer will latch the /STB data at the position edge. DATA BIT0(LSB) DATA BIT1 DATA BIT2 DATA BIT3 DATA BIT4 DATA BIT5 DATA BIT6 DATA BIT7 (MSB) The printer acknology, indicate that the printer /ACK has fineshed one byte data reading.

  • Page 9: Connect The Cash Drawer

    - 6 - POS-58 User Manual To computer 2.4 Connect the cash drawer The printer use RJ-11 6line socket., support most 12V/24V cash drawer. Connecting the cash drawer as the followed picture: Connect cash Cash drawer socket definiction: DEFINITION Cash drawer open control +24V POWER Cash drawer open control...

  • Page 10: Control Panel

    - 7 - POS-58 User Manual 3 3 3 3 USING USING USING PRINTER PRINTER USING THE THE PRINTER PRINTER 3.1 Control Panel 3.2 Online and Offtline The “LINE” buttons will toggle the printer with on “online”, “offline”mode. NOTE: NOTE: NOTE: NOTE: When powered up, the printer will stay in the “online”...

  • Page 11: Install The Paper Roll

    - 8 - POS-58 User Manual In debug mode, POS-58 will prints all commands and datas in hexadecimal format as follows: 1B21 001B 2602 4040 .!..&.@@ 4040 020D 1B44 0A14 @@...D.. 1E28 2828 0001 0A41 .(((...A 0D42 0A43 4343 4445 .B.CCCDE Note: In debug mode, POS-58S, POS-58U will change the baudrate with “online”...
  • Page 12 - 9 - POS-58 User Manual 1. open the cover 2. stick a little pure alcohol by cotton bud 3. Use the cotton bud to scrub the surface of thermal printing scale smoothly 4. be sure that the alcohol is volatilized before you use the machine again 4 4 4 4 TROUBLE TROUBLE TROUBLE...

  • Page 13: Set Of Command

    - 10 - POS-58 User Manual 5 5 5 5 ESC/POS ESC/POS ESC/POS PRINTING PRINTING COMMAND COMMAND ESC/POS PRINTING PRINTING COMMAND COMMAND SET 5.1 Set of Command Type Command Name Print and line feed Print Command ESC J Print and Feed n dots paper ESC 2 Select default line spacing Line spacing...

  • Page 14: Command Detail

    - 11 - POS-58 User Manual ESC W … Set printing area in page mode ESC $ nL nH Set absolute print X position GS $ nL nH Set absolute print Y position ESC \ nL nH Set relative print X position GS \ nL nH Set relative print Y position GS L nL nH...

  • Page 15: Character Command

    - 12 - POS-58 User Manual ESC 3 n Set line spacing Format ASCII ESC 3 n Decimal 27 51 n Hexadecimal 1B 33 n Description n = 0-255 ESC 3 n sets the line spacing to n dots. The default value is 30 ESC a n Select align mode Format...
  • Page 16 - 13 - POS-58 User Manual ESC DC4 Disable Double Width mode Format ASCII ESC DC4 Decimal 27 20 Hexadecimal 1B 14 Description Disable Double Width mode ESC { n Set/Cancel Character Updown mode Format ASCII ESC { n Decimal 27 123 n Hexadecimal 1B 7B n Description n=1:Enable Updown mode n=0:Disable Updown Mode...

  • Page 17: Bit Image Command

    - 14 - POS-58 User Manual d2 d4 d6 ESC ? n Disable user-defined character Format ASCII ESC ? n Decimal 27 37 n Hexadecimal 1B 25 n Description ESC ? n disable user-defined characters, printer will use the interal character. ESC R n Select an internal character set Format...

  • Page 18: Cash Drawer Control Command

    - 15 - POS-58 User Manual dx=0-255 k = nL+256*nH (m=0,1) k = (nL+256*nH)*3 (m=32,33) The modes selected by m are as follows: 0：8dots single density，102dpi 1: 8dots double density，203dpi 31:24 dots single density,102dpi 32:24 dots double density,203dpi The bit image format is the same as user-defined character. GS / n Print downloaded bit image Format...

  • Page 19: Key Control Command

    - 16 - POS-58 User Manual Hexadecimal 1B 70 m n1 n2 Description Send a pulse to the specified connector pin. It is used to open the cash drawer. m：special the pin the pulse is send to. 0:pin2, 1:pin5 n1,n2:pulse on & off time. (unit:2ms) 5.2.6 Key control command ESC c 5 n Enable/Disable the panel key...

  • Page 20: Bar Code Command

    - 17 - POS-58 User Manual GS a n Enable/Disable Automatic Status Back(ASB) Format ASCII GS a n Decimal 29 97 n Hexadecimal 1D 61 n Description POS-58P don’t support this command，Only in serial type printer effective. n definition as follows: Value Function Disable/Enable ASB...
  • Page 21 - 18 - POS-58 User Manual Description 0 ≤ n ≤3 48 ≤ n ≤51 This command selects the printing position for human readable characters when printing a barcode. The default is n=0. Human readable characters are printed using the font specified by GS fn. Select the printing position as follows: Printing Positioin 0,48: Not printed...
  • Page 22 - 19 - POS-58 User Manual 2,67 EAN13 12,13 48-57 3,68 EAN8 48-57 4,69 CODE39 >1 32,36,37,43,45-57,65-90 >1 5,70 48-57 even number 6,71 CODEBAR >1 36,43,45-58,65-68 7,72 CODE93 >1 0-127 8,73 CODE128 >1 0-127 9,74 CODE11 >1 48-57 10,75 >1 48-57 If materials are illegal characters, printer will not print the barcode If the bar code more than effective print width, the printer results unknown.
  • Page 23 - 20 - POS-58 User Manual Decimal 27 87 sxL sxH syL syH wxL wxH wyL wyH Hexadecimal 1B 57 sxL sxH syL syH wxL wxH wyL wyH Description Set the page size and margin Left margin: sxL+256*sxH Top margin: syL+256*syH Width: wxL+256*wxH Height :...

  • Page 24: Appendixa：code Page

    - 21 - POS-58 User Manual 6 6 6 6 Sample Sample Sample Programming Programming Sample Programming Programming The following sample suggest that “putchar(ch)” send one byte ch to the PD02. Sample: putchar(27); putchar(‘=’); putchar(1); // set printer online putchar(27); putchar(‘t’); putchar(0); // code page PC 437 putchar(29);...
  • Page 25 - 22 - POS-58 User Manual ­ ˇ § ÷ ¸ ° ¨ ˙ ■ ˝ ˛ ˘ ű Ř ř PC857 PC857 PC857 PC857 Ç ü é â ä à å ç ê ë è ï î Ä Å É...
  • Page 26 - 23 - POS-58 User Manual APPENDIXB International characters APPENDIXB International characters APPENDIXB APPENDIXB：International International characters characters...
  • Page 27 - 24 - POS-58 User Manual APPENDIXC Persian characters APPENDIXC Persian characters APPENDIXC APPENDIXC：Persian Persian characters characters...
  • Page 29 User Manual v.201811...

This manual is also suitable for:

P58

Table of Contents