Advertisement
Quick Links
FUEL AND IGNITION
2012 Harley Davidson Vrod
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
15-023
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
CD-ROM
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro
1
Alcohol swab
1
O2 Optimizer front
1
O2 Optimizer rear
1
Zip tie
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2012 HD V-rod PCV - 1
Advertisement
Related Manuals for Dynajet POWER COMMANDER V
Summary of Contents for Dynajet POWER COMMANDER V
- Page 1 PARTS LIST Power Commander USB Cable CD-ROM FUEL AND IGNITION Installation Guide Power Commander Decals 2012 Harley Davidson Vrod Dynojet Decals Velcro I n s t a l l a t i o n I n s t r u c t i o n s Alcohol swab O2 Optimizer front O2 Optimizer rear...
-
Page 2: Usb Connection
POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can use USB CONNECTION any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. Used for clutchless full throttle upshifts. Insert Shifter- the wires from the Dynojet quickshifter into either INPUT 1 or INPUT 2. The polarity of the wires is not important. ANALOG Speed- Not needed on Harley applications as the SPEED speed signal wire is built into the main wiring EXPANSION PORTS 1 & 2 INPUT 2B harness of the PCV. - Page 3 FIG.A Remove the seat. Remove the two bolts that hold on the rear fender cover (Fig. A). FIG.B Unplug the stock wiring harness from the ECM (Fig. B). Ground wire FIG.C Plug the PCV in-line of the stock wiring harness and ECM (Fig. C). Route the harness as shown in Figure C. Use the supplied zip tie to secure the connectors in place. 15-023 www.powercommander.com 2012 HD V-rod PCV - 3...
- Page 4 FIG.D Install the rear fender cover. Use the supplied velcro to secure the PCV in place (Fig. D). Make sure to use the alcohol swab to clean the surface before attaching. Locate the stock rear O2 sensor connection and unplug it (Fig. D). This is a BLACK 4 pin connector. 10 Plug one of the Dynojet O2 Optimizers into the stock wiring harness. The Optimizers are indexed so they can not be installed incorrectly. FIG.E 11 Locate the stock front O2 sensor connection and unplug it (Fig. E). This is a WHITE 4 pin connector located on the left side of the radiator.
- Page 5 FIG.G Remove the right hand side cover by the steering stem (Fig. G). FIG.H Remove the rubber plug for the diagnostic connector. Using the OPTIONAL (76950159) V-rod extension lead plug one end of the lead into the stock diagnostic connector (Fig. H). Route the Autotune harness along the right side of the airbox and plug Diagnostic plug the other end into the Autotune kit. ATTENTION If you do not have the OPTIONAL (76950159) Power Extension Lead cut off the connector from the Autotune module. Connect the RED wire to a switched 12v source. Connect the BLACK wire to Ground. FIG.I Connect the longer harness to the front O2 sensor. Route the harness along the front down tube and along the backbone of the frame to the...
- Page 6 FIG.J Use the CAN bus cable to connect one Autotune module to the PCV. It does not matter what ports are used. Install the CAN termination plug into the open port of the Autotune module. 10 Secure the harnesses in place as to not contact the exhaust. 11 Reinstall the seat, rear fender cover, and side cover. Go to www.powercommander.com for maps and software updates. 15-023 www.powercommander.com 2012 HD V-rod PCV - 6...
Need help?
Do you have a question about the POWER COMMANDER V and is the answer not in the manual?
Questions and answers