Related Manuals for UniFi AC Mesh
Summary of Contents for UniFi AC Mesh
- Page 1 Package Contents UniFi AC Mesh Antennas (Qty. 2) Wall Mount Bracket Screws (Qty. 2) Screw Anchors (Qty. 2) Zip Ties (Qty.2) Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
-
Page 2: Installation Requirements
Gigabit PoE (24V, 0.5A) with Power Cord* Mount Bracket* Fast-Mount Adapter * Included only in the single-pack of the UAP-AC-M Installation Requirements Wall-mounting: Drill and 6 mm drill bit Phillips screwdriver Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE. -
Page 3: System Requirements
Diagram Showing Use of Ethernet Surge Protectors IMPORTANT: The UAP-AC-M requires the UniFi Controller v5.4 or higher, available at: ui.com/download/unifi System Requirements Linux, Mac OS X, or Microsoft Windows 7/8/10 Create PDF in your applications with the Pdfcrowd HTML to PDF API... - Page 4 UniFi Controller software v5.4 or newer (available at: ui.com/download/unifi) Wireless Adoption Requirements The UAP-AC-M supports wireless adoption into your UniFi Wi-Fi network. This feature requires a currently managed UniFi AP operating with the following configuration: The UniFi AP must be running firmware v3.7.7 or newer...
- Page 5 LAN and DHCP server. Power can be provided by one of the following: Gigabit PoE adapter (included) Ubiquiti UniFi Switch with PoE 802.3af PoE compliant switch Note: The UAP-AC-M supports 802.3af/A PoE and 24V Passive PoE. It does NOT support 802.3af/B PoE and therefore does not work with...
-
Page 6: Hardware Installation
Press and hold the Reset button for more than five seconds until the Status LED turns off. Hardware Installation The UniFi AP can be mounted on a wall, pole, or fast-mount of a Ubiquiti high-gain antenna. Perform the steps for the appropriate installation: Wall Mount... - Page 7 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 8 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 9 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 10 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
-
Page 11: Pole Mount
Pole Mount Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD... - Page 12 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 13 Fast-Mount Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 14 The included Fast-Mount Adapter allows the UniFi AP to be mounted on a Ubiquiti high- gain antenna equipped with a fast-mount radio mounting bracket. Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
-
Page 15: Attach Antennas
Attach Antennas 1. Ensure the Rubber Gaskets remain in place. Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD... - Page 16 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 17 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
-
Page 18: Connecting Ethernet
Connecting Ethernet Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD... - Page 19 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 20 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 21 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
- Page 22 Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
-
Page 23: Connecting Power
Connecting Power Note: The UAP-AC-M supports 802.3af/A PoE and 24V Passive PoE. It does NOT support 802.3af/B PoE and therefore does not work with 802.3af/B switches. Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD... - Page 24 Optional Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
-
Page 25: Software Installation
Wireless Adoption “Wireless Adoption Requirements” before proceeding. 1. Ensure the UniFi AP is powered on, and then launch the UniFi Controller software. 2. Go to the Devices page, and the UAP-AC-M will show up as Pending Adoption (Wireless). 3. Click Adopt. -
Page 26: Mobile App Installation
Controller software, refer to the User Guide. Mobile App Installation Ubiquiti also offers the UniFi app, which is available from the App Store® (iOS) or Google Play™ Store (Android). You can use it to provision a UniFi AP for basic functionality without configuring a UniFi Controller. -
Page 27: Installer Compliance Responsibility
Installer Compliance Responsibility This device must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements. Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD... - Page 28 Antenna Select your antenna from the list. Transmit output power is automatically adjusted to comply with the regulations of the applicable country. For a Custom antenna, Antenna Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...
-
Page 29: Specifications
Gain is entered manually. Note the requirements and antenna types listed below. Certified Antenna Types This radio transmitter FCC ID: SWX-UAPACM / IC: 6545A-UAPACM has been approved by FCC / ISED Canada to operate with the antenna types listed below with the maximum permissible gain for each antenna type indicated. -
Page 30: Antenna Gain
UAP-AC-M Power Save Supported Max. Power Consumption 8.5W Operating Frequency 2.4 GHz 5 GHz Max. TX Power 2.4 GHz 20 dBm 5 GHz 20 dBm Antennas (2) External Dual-Band Omni Antennas (1) Panel Antenna* Wi-Fi Standards 802.11a/b/g/n/ac Wireless Security WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES) BSSID Up to Four per Radio... -
Page 31: Safety Notices
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. -
Page 32: Limited Warranty
e. Protective bonding must be installed in accordance with local national wiring rules and regulations. Limited Warranty ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. - Page 33 CAN ICES-3(A)/NMB-3(A) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
- Page 34 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. AVIS IMPORTANT Déclaration sur l’exposition aux rayonnements Cet équipement est conforme aux limites prévues pour l’exposition aux rayonnements dans un environnement non contrôlé. Lors de l’installation et de la mise en fonctionnement de l’équipement, assurez-vous qu’il y ait une distance minimale de 20 cm entre l’élément rayonnant et vous.
-
Page 35: Weee Compliance Statement
Country List BFWA (Broadband Fixed Wireless Access) members noted in blue Note: This device meets Max. TX power limit per ETSI regulations. The following apply to products that operate in the 5 GHz frequency range: Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz frequency range within all member states. - Page 36 © 2020 Ubiquiti Inc. All rights reserved. Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD...