Advertisement
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
I m p o r t a n t
S a f e t y
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electrical shock and
injury to persons, including the following:
If the appliance is damaged, check with the
supplier before installation and operation.
D o
n o t
u s e
Do not use in the immediate surround-
ings of a bath, shower or swimming pool.
Do not locate the appliance immediately be-
low a fixed socket outlet or connection box.
The appliance carries the Warning symbol
DO NOT COVER, indicating that it must
n o t b e c o v e r e d .
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and knowl-
edge if they have been given supervision or
instruction concerning use of the appliance
in a safe way and understand the hazards
involved. Children shall not play with the ap-
pliance. Cleaning and user maintenance shall
not be made by Children without supervision.
Children of less than 3 years should be
kept away unless continuously supervised.
Children aged from 3 years and less than 8
years shall only switch on/off the appliance
provided that it has been placed or installed
in its intended normal operating position and
they have been given supervision or instruc-
tion concerning use of the appliance in a safe
way and understanding the hazards involved.
Children aged from 3 years and less than 8
years shall not plug in, regulate and clean
the appliance or perform user maintenance.
Do not use this appliance in series with a
thermal control, a program controller, a timer
or any other device that switches on the heat
automatically, since a fire risk exists when the
appliance is accidentally covered or displaced.
Ensure that furniture, curtains or other
combustible material are positioned no
closer than 1 metre from the appliance.
In the event of a fault unplug the appliance.
U n p l u g
t h e
a p p l i a n c e
n o t r e q u i r e d f o r l o n g p e r i o d s .
Although this appliance complies with safety
standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
T h e
a p p l i a n c e
tioned so that the plug is accessible.
If the supply cord is damaged it must be replaced
by the manufacturer or service agent or a simi-
larly qualified person in order to avoid a hazard.
K e e p
t h e
s u p p l y
f r o m t h e f r o n t o f t h e a p p l i a n c e .
Warning: In order to avoid overheating,
do not cover the appliance. Do not place
material or garments on the appliance, or
obstruct the air circulation around the appli-
ance, for instance by curtains or furniture, as
this could cause overheating and a fire risk.
A d v i c e .
o u t d o o r s .
.
.
.
.
w h e n
m u s t
b e
p o s i -
c o r d
a w a y
Warning: In order to avoid a hazard due
to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied
through an external switching device, such
as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
CAUTION - Some parts of this product
can become very hot and cause burns.
Particular attention has to be given where
children and vulnerable people are present.
Technical Information
Model No: CLB20E, CVL20E
Heat Output
Nominal Heat Output
Minimum Heat Output
Maximum Continous Heat Output P
Auxiliary Electricity Consumption
In Standby mode
with mechanic thermostat room temperature control.
General
Unpack the heater carefully and retain the packaging for possible future
use, in the event of moving or returning the fire to your supplier.
These models are designed to be free standing and are normally
positioned against a wall.
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of
the year. Using the flame effect on its own only requires little electricity.
A choice of 1kW or 2kW heat output is provided by the fan heater, which
is located at the bottom of the unit.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Please note: Used in an environment
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage. Before
switching on, please read the safety warnings and operating instructions.
Controls
- see Fig. 2
These switches provide a choice of heat settings, The appliance is in
standby mode when the mainslead is plugged in. This is indicated by the
red neon behind the flame effect screen.
two selector switches are in the ON position when the side with the
markings on (i.e. I, or II) is pushed in.
Selector switch 1 (0) Controls the electricity supply to the
appliance and flame effect. Press for 'ON'
and 'Standby'. If both selector switches 2 and
3 are in the OFF position, the product works
on flame effect only.
Selector Switch 2 (I) Provides 1kW heat output
Selector Switch 3 (II) Provides 2kW output with switch 2
UK
230V
240V
P
1.8
-
1.9
kW
Nom
P
0.9
-
1.0
kW
min
1.8
-
1.9
kW
max,c
el
0.37
-
0.41
W
SB
where background noise is very
The
Advertisement
