Advertisement
Minimum Height - Ram to Table: ................................ 157mm
nett Weight: ................................................................... 73kg
optional Accessories: .................................................YKPP8
overall Height: ........................................................... 965mm
Ram diameter: .......................................................... Ø43mm
Ram Stroke: ............................................................... 160mm
Table Aperture: ........................................................... 140mm
Type: ....................................................................... Hydraulic
Working Table depth: ................................................. 156mm
Working Table Width: ................................................. 600mm
4. ASSEMBLY
4.0.1.
Attach slings around the top cross member, using a suitable hoist or gantry lift the main frame (fig.1.15) out of the transportation crate
into an upright position.
Keep the main frame (fig.1.15) held safely upright. DO NOT allow to fall. Attach base sections (fig.1.11) with supports (fig.1.10) to the
4.0.2.
left and right hand posts. only fully tighten the securing nuts and bolts when the base sections (fig.1.11) are square to the main frame.
4.0.3.
Attach the hydraulic unit (fig.1.43) to the right hand post of the main frame (fig.1.15).
4.0.4.
Connect the hydraulic hose (fig.1.40) from the hydraulic unit (fig.1.43) to the union on the union seat (fig.1.36) in the top cross
member of the main frame (fig.1.15).
locate the pressure gauge hole in the union seat (fig.1.36) and remove the plug with a hex key (this may be very tightly secured).
4.0.5.
Screw the pressure gauge (fig.1.41) into the union seat (fig.1.36).
4.0.6.
Hold bed frame (fig.1.6) in position with bed frame pins (fig.1.8) and secure with the safety clips (fig.1.7).
fig.1
Item
Part No.
Description
5. INSTALLATION
1
GSM88.S
GRUB SCREW M8x8 (SINGLE)
5.0.1.
Securely attach the press to a flat, firm, level surface taking into account
2
YK15FFP.02
SPRING
clearance for workpieces.
3
SB-5.6
STEEL BALL 5.6mm
▲
DANGER! The press is heavy. If it requires moving after assembly or for
relocation, use suitable slings around the top crossbeam, or lift direct with a
4
YK15BP.04
V-BLOCK
forklift with the forks located under the top crossbeam.
5
YK15FFP.05
SCREW
5.1.
Purge hydraulic system.
6
YK15BP.06
BED FRAME
Before operating the press, the hydraulic system may require purging in
order to eliminate any air that may have built up during transit.
7
YK15BP.07
RETAINING CLIP
open the release valve (fig.2) by turning anti-clockwise and pump the
8
YK15BP.08
PIN, TABLE SUPPORT 265x19mm
handle several times. Should the system malfunction at any time, repeating
this procedure may resolve the problem.
9
YK15BP.09
BOLT
DANGER! The press is purpose designed to withstand greater loads than
▲
10
YK30FFP.10
SUPPORT
the hydraulic unit can develop. For safety reasons, always ensure the
workpiece is secured on the table to ensure loads that flex will not suddenly
11
YK15FFP.11
BASE SECTION
"give" causing danger to operator or damage to component. ensure you
12
YK15BP.12
WASHER
have read and understood chapter 1 safety instructions.
13
YK15BP.13
LOCK WASHER
5.2.
SETTING THE WORKING TABLE HEIGHT
5.2.1.
To set the working table at the desired height it is advisable to obtain
14
YK15BP.14
NUT
assistance due to the weight of the working table. Remove the pressing
15
YK15BP.15
FRAME
plate/V-blocks from the working table then remove the safety clips and the
pins. Position the working table at the required operating height, insert the
16
YK15BP.16
BOLT
pins into the appropriate holes in the uprights and fit safety clips.
17
YK15FFP.17
SERRATED SADDLE
© Jack Sealey limited
18
YK15FFP.18
RAM NUT
19
YK15FFP.19
UNDER PLATE
Parts Information:
Hydraulic Press Premier 15tonne Bench
Type
Model No: YK15BP
Item
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Original Language Version
41
42
Part No.
Description
YK15FFP.24
UPPER ROUND NUT
YK15FFP.25
SPRING
YK15FFP.26
SCREW
HHB10100.S
HEX HEAD BOLT M10x100mm SINGLE
YK15FFP.28
RAM
YK15FFP.29
OIL HOSE (FOR RAM)
YK50FFP.51
O-RING
YK50FFP.62
JOINT
YK50FFP.45
ELBOW FITTING
YK15BP.33
NUT
YK15BP.34
LOCK WASHER
YK15BP.35
WASHER
YK15FFP.36
UNION SEAT
YK50FFP.56
UNION NUT
YK50FFP.57
UNION SCREW
YK759FAH.61
NYLON RING
YK15BP.40
OIL HOSE (FOR PUMP)
YK15FFP.40
PRESSURE GAUGE
YK15BP.42
BOLT
fig.2
YK15BP Issue 2 07/08/18
Advertisement
