Advertisement
Quick Links
Advertisement
Related Manuals for SY SY-SE-10
Summary of Contents for SY SY-SE-10
- Page 1 SY-SE-10 18G HDMI 2.0 Up/Down Scaler (with image Enhancer) EDID Manager, HDCP controller & Audio De-embedder SY Electronics Ltd., 7 Worrall Street, Salford, Greater Manchester, M5 4TH Tel: +44 (0)161 868 3450 – Fax: +44 (0)161 868 3459 Web: sy.uk...
- Page 2 The SY-SE-10 provides HDMI image scaling for both 2K to 4k (upscaling) and 4K to 2K (downscaling), with image enhancement settings in the upscaling mode. The SE-10 has a wide range of EDID settings that should cater for most situations, including a programmable EDID setting for those more troublesome times.
- Page 3 HDMI output to display device HDMI Signal Out LED Using the SY-SE-10 The SE-10 is placed in between the HDMI output device (Source) and the HDMI display device (Sink) and powered via the mini USB connector by the supplied PSU - see Figure 3.
-
Page 4: Edid Settings
Ensure there is an HDMI sink device connected to the HDMI OUT connector. Set S6 to ON (↓). Within 2 seconds set S6 to OFF (↑), the USER EDID memory is now programmed with the EDID data read from the HDMI sink device and is ready for use. sy.uk V1.2... -
Page 5: Other Settings
HDBaseT Mode 2 – See below ↓ ↑ ↑ HDBT Mode 2 Output bandwidth limited to 9Gbps ↓ ↑ ↓ TP 1 – 1080p 1080p60 Test Pattern mode ↓ ↓ ↑ TP 2 – 4K30 4K30Hz Test Pattern mode V1.2 sy.uk... - Page 6 Figure 1 – 1080p60 Test Pattern Figure 2 - 4K30 Test Pattern Test Pattern Resolution Settings Setting Resolution Details Sub sampling Rate (Gbps) Clock (MHz) 1080p60 1920 x 1080p @ 60Hz 4:4:4 4.46 148.5 4K30 3840 x 2160p @ 30Hz 4:4:4 8.91 297.0 sy.uk V1.2...
-
Page 7: System Configuration
System Configuration Figure 3 - SE-10 as an EDID Manager or Image Scaler V1.2 sy.uk... - Page 8 Figure 4 – Example of SE-10 with Extenders, in HDBT Mode 1 Setting sy.uk V1.2...
- Page 9 Figure 5 – Example of SE-10 with Extenders, in HDBT Mode 2 Setting V1.2 sy.uk...
- Page 10 Note: The status information may be updated either by RS232 commands or by changing the switches on the front panel. The status information will always be from the last change of state that occurred before the get status request was made. sy.uk V1.2...
- Page 11 HDBT Mode 1 Limit the output bandwidth to 10.2G for any input signal above 10.2G HDBT Mode 2 Limit the output bandwidth to 10.2G for any input signal above 10.2G See HDBT Modes above for more details about how the two HDBT Modes operate. V1.2 sy.uk...
- Page 12 0 – for the 1080p60 pattern, or 1 – for the 4K30 pattern. The returned value of x depends on the last change that occurred either Actual Value: by the RS232 SET command or the front panel Scale/TP switches. sy.uk V1.2...
- Page 13 4K60Hz 3D 6CH HDR 4K @ 60Hz with support for 3D and HDR and 5.1 audio 4K60Hz 3D 8CH HDR 4K @ 60Hz with support for 3D and HDR and 7.1 audio User EDID User programmable EDID memory V1.2 sy.uk...
-
Page 14: Specifications
Pass through Bandwidth 18 Gbps maximum Audio General Digital Audio Supports all audio including PCM, Dolby True HD, DTS, DTS-HD Analogue Output Stereo audio output Frequency Response 20Hz ~ 20KHz Output Connector 1 x 3.5mm stereo jack (L/R) sy.uk V1.2... - Page 15 Damage to the product due to incorrect usage or storage Damage caused by unauthorised repairs Damage caused by mistreatment of the product Please direct any questions or problems you may have to your local dealer before contacting SY Electronics. V1.2...
- Page 16 NOTES sy.uk V1.2...
Need help?
Do you have a question about the SY-SE-10 and is the answer not in the manual?
Questions and answers