Advertisement
Quick Links
Advertisement
Related Manuals for Calandra Racing Concepts Carpet Knife Generation X Series
Summary of Contents for Calandra Racing Concepts Carpet Knife Generation X Series
- Page 1 Gen-X 10 LE...
- Page 2 Center Pivot Center Pivot Cap Alum Pivot ball 2-56 Button Head Bag 1 Center Pivot Base Assemble the Molded Center Pivot assembly as shown. Tighten the 2-56 button head screws [4] enough to remove any up and down play, be sure the flanged pivot ball [2] pivots freely.
- Page 3 One-Piece 4-40 x 5/16” Red Low- 4-40 x ½” Side Links 2-56 Button Head FH steel Profile Ball FH Steel Bag 2 1 - In Bag 2, find the graphite bottom plate [10]. Secure it to the pivot ball assembly with the ½” flat head screw [5].
- Page 4 Rear X-Pod 2-56 Steel 4-40 x 1/4” Red Alum 4-40 x 1/4” Red Locknut Ballstud - Black 4-40 Ballstud Button Head Flat Head Bag 3 Motor Plate Graphite Top Plate Left Side Plate 1 - Install the black 2-56 ballstuds [15] into the graphite top plate [16]. These steel balls thread into the graphite, no nut is needed.
- Page 5 Tweak Plates 4-40 x 3/8” Molded Plastic set screw Spring Holder Bag 4 NSERT WEAK CREWS IN RACE SSEMBLY 1 - Place the Tweak Brace [25] on a smooth, flat table and thread the Tweak set screws [23] into the brace per the illustration. Try to be careful to thread it in straight and perpendicular.
- Page 6 1 - Mount the completed tweak brace assembly to the chassis as shown using the 4-40 x 1/4” flat head screws [22]. Do this for both left and right side tweak plates. 2-56 set- 4-40 x 5/16” 2-56 Plastic Short 4-40 Plastic Damper Tubes screw stud set screw...
- Page 7 Battery Top Deck Red 3/4” Red Low- 4-40 x 1/4” 4-40 x 1/4” 4-40 x 3/8” Standoff Profile Ball Button Head Flat Head Flat Head Bag 6 1 - Bolt the 3/4” hex standoffs [37] to the chassis using four 1/4” flat head screws [22]. 2 - Mount the plastic battery blocker pieces [38] to the chassis by fitting them into the holes as shown below, and then secure in place with 1/4”...
- Page 8 Center Shock Red Alum 4-40 x 3/8” 4-40 x 1/8” 4-40 Ballstud Flat Head Set Screw Bag 7 Antenna / Shock Mount 1 - Thread the spring adjuster nut [42] onto the shock body [43] as shown above. *This needs to be installed first or you will not be able to get it on later after the lower end of the shock is assembled!* 2 - Insert only 1 of the small o-rings [44] into the lower end of the shock body [43].
- Page 9 Plastic Ride Height Spacers 3, 4, 5mm Hinge Pin 2-56 BH CRC Pro-Strut Delrin 2-56 Red Pivot Ball Locknut Front End Bag F Upper Cap 4-40 x 7/16” Caster Shim Flat Head 2-56 x ½” SH 1 - Pop the delrin pivot ball [56] into the lower arm [57]. Place the arm on a strong table and push the ball in with the back of screwdriver handle.
- Page 10 4-40 x 1/4” Red Low- Graphite 2-56 SH Dual Axle King Pin Button Head Profile Ball Steering Arm CRC Pro-Strut Upper Progressive E-Clip Brass Set Nylon Spring Ball Front End - cont. Conical Spring Screw 1 - Build up the left and right steering blocks [68] as shown to the left. Start by threading the button head screw [18] through the graphite steering arm [69] and into the red low profile ball [12].
- Page 11 8-32 x 5/8” 4-40 x 3/8” 4-40 x 5/16” CRC Pro-Strut Low Head Gray #4 Washer Red Locknut Flat Head Red FH F.E. Screw Front End - cont. Installing the Lower arm to the Chassis 1 - Insert four 4-40 x 3/8” FH screws [41] through the chassis, and then place two #4 washers [81] over each of the screws before sliding them through the Front End Plate [79].
- Page 12 Red Low- 4-40 x 5/16” 4-40 x 1/4” Washer Red Locknut CRC Pro-Strut Profile Ball FH steel Button Head Front End - cont. Futaba 9650, Adjustable Servo Mounts KO 949, Hitec 225, and Airtronics/Sanwa - The Gen-X 10 is equipped with an adjustable servo mounting system that will let 94141 and 94145 you use a variety of servos from different manufacturers.
- Page 13 Ride Height Inserts Bag 8 1/4” x 3/8” 1/4” Shim 4-40 x 3/8” Flanged Bearing Steel Socket Cap Differential Axle 1 - Locate the tree of ride height inserts [88]. Select an insert that will work best with your tire size (example - the #2 spacers will give you about 5mm .
- Page 14 4-40 x 3/8” 4-40 x 1/8” Button Head Set Screw Bag 10 OSTS 1 - Secure the body posts [103] to the front bumper [83] and the tweak plates [25] with the steel button head screws [28]. The tweak plates have four body mount locations to accommodate numerous body sizes and styles.
- Page 18 CRC Gen-X 10 2008 IIC Winner - Las Vegas 2008 - U.S. Indoor Champs T.Q. + 1st - Cleveland 2009 IIC Top Qualifier - Las Vegas 2009 Halloween Classic T.Q. + 1st 2009 U.S. Indoor Champs T.Q. + 1st - 13.5 Class 2009 U.S.