Subscribe to Our Youtube Channel
Related Manuals for Calandra Racing Concepts Battle Axe 2.0
Summary of Contents for Calandra Racing Concepts Battle Axe 2.0
- Page 1 Battle Axe 1:10th Oval Weapon from Team CRC Assembly Manual servo and saver not included Part # 1900 Calandra Racing Concepts 6785 Martin Street ~ Rome, NY 13440 Tel + Fax 315-338-0867 ~ www.teamcrc.com...
- Page 2 Center Pivot Center Pivot Base Alum Pivot ball 2-56 Button Head Bag 1 Center Pivot Cap Assemble the Molded Center Pivot assembly as shown. Tighten the 2-56 button head screws [4] enough to remove any up and down play, be sure the flanged pivot ball [2] pivots freely.
- Page 3 One-Piece Red Low- 4-40 x 5/16” 4-40 x ½” Red 7/8” 2-56 Button Head Side Links Profile Ball FH steel FH Alum Standoff Bag 2 1 - In Bag 2, find the graphite bottom plate [10]. Secure it to the center pivot assembly with the ½”...
- Page 4 Rear X-Pod Red Aluminum 4-40 x 3/16” 4-40 x 1/4” 4-40 x 1/4” Washer Female Ballstud Red Button Head Red Button Head Red Alum FH Bag 3 Graphite Micro Left Side Graphite Motor Plate Top Plate Pod Plate X-brace 1 - Insert a 1/4” red button head screw [22] through the bottom of the front hole on the graphite top plate [17] so that the threads point upward.
- Page 5 Tweak Plates 4-40 x 1/4” 4-40 x 3/16” Red 7/8” Red Button Head Red Button Head Standoff Bag 4 Graphite Tweak Red Aluminum Plate (x2) 4-40 x 1/4” Female Ballstud Red Alum FH 1 - Place the Tweak Plate [24] in front of you so the holes face the same direction as the picture.
-
Page 6: Side Shocks
Side Shocks CRC Dura-Shock Assembly Instructions Bag 5 ***Pre assembly inspection - Take the shock shaft and slide it through the black Delrin insert. Be sure the shaft slides through freely. If the shaft drags on the Delrin, simply spin an X-acto Knife tip in each end of the delrin piece. The knife will remove the small manufacturing burr that occasionally forms right near the end of the hole. - Page 7 4-40 x 1/4” Center Shock Mount 4-40 x 5/8” Red Alum FH Steel Cap Head 4-40 x 1/4” Bag 6 Steel Cap Head Brass Washer Red Locknut Aluminum Shock / Antenna Mount Graphite Shock Mount Plates (x2) NOTE - The ball pictured here is not 1 - Assemble shock mount as shown by inserting two included in this step.
- Page 8 Plastic Ride Height Spacers 3, 4, 5mm 2-56 Button Head Hinge Pin CRC Pro-Strut Delrin 2-56 Red Pivot Ball Locknut Front End Bag F Upper Cap 4-40 x 7/16” Caster Shim Red FH 2-56 x ½” SH 1 - Pop the delrin pivot ball [30] into the lower arm [31]. Place the arm on a strong table and push the ball in with the back of screwdriver handle.
- Page 9 4-40 x 1/4” Red Low- Graphite 2-56 SH Dual Axle King Pin Red Button Head Profile Ball Steering Arm CRC Pro-Strut Upper E-Clip Brass Set Nylon Spring Ball Front End - cont. Side Spring Screw 1 - Build up the left and right steering blocks [42] as shown to the left. Start by threading the red button head screw [22] through the graphite steering arm [43] and into the red low profile ball [12].
- Page 10 8-32 x ½” CRC Pro-Strut 4-40 x 5/16” Low Head 4-40 x 7/16” Red Locknut Red FH F.E. Screw Red FH Front End - cont. Installing the Lower arm to the Chassis 1 - Insert three 4-40 x 7/16” red FH screws [36] through the chassis, then through the Front End Riser Plate [53], and top with the Front End Mounting Plate [54].
- Page 11 4-40 x 1/4” 4-40 x 5/16” Red Alum 4-40 x 3/8” CRC Pro-Strut Red Button Head Red Locknut Red FH 4-40 Ballstud Red Socket Cap Washer Front End - cont. Front of Car Adjustable Servo Mounts The Battle Axe is equipped with an adjustable servo mounting system that will let you use a variety of servos from different manufacturers.
- Page 12 Ride Height Inserts Bag 8 1/4” x 3/8” 1/4” Shim 4-40 x 3/8” Flanged Bearing Steel Socket Cap Differential Axle 1 - Locate the tree of ride height inserts [64]. Select an insert that will work best with your tire size .
- Page 13 4-40 x 3/8” M3 x 8mm Steel 4-40 x 1/8” Red Socket Cap Button Head Set Screw Bag 10 OSTS 1 - Secure the shorter front body posts [79] to the front bumper with Adjust body height the steel button head screws [80]. by raising or lowering this collar 2 - Mount the longer rear body posts [81] to the Tweak Plates, using...
-
Page 16: Front End
Front End: Track Width Wheel Base Axles Camber Caster Shims Caster Blocks Spring King Pin Length Lube Upper Arm Length Upper Arm Height Ackerman Ride Height Spacer Riser Plate Chassis Stiffener Center: Shock Spring Shock Oil Shock Mnt Height Battery Battery Position Shock Mnt Length Rear End:...
Need help?
Do you have a question about the Battle Axe 2.0 and is the answer not in the manual?
Questions and answers