Campbell Hausfeld CC2410 Operating Instructions Manual page 2

Cordless Inflator & 12-Volt Power Pack
12-VOlt DC reChArGInG
This unit is NOT
intended for
recharging a car battery.
Never start the
car (vehicle) when
the 12-volt DC recharging adapter is
plugged into the 12-volt DC power
outlet.
nOte: Charging the battery while the
car engine is not running drains the car
battery and is not recommended. If the
unit is used too long after the yellow
light comes on, recharging time could
take up to 7 hours.
To recharge the battery using the
12-volt DC adapter while driving, follow
the subsequent procedures:
1. Insert the 12-volt DC recharging
adapter into the 12-volt DC output
socket on the inflator.
2. Insert the other end into the 12-volt
DC power outlet on the vehicle.
Rotate to make a good electrical
contact.
3. The inflator should be charged for
5 to 6 hours while driving before
the initial use. After multiple uses,
recharge the inflator for 3 hours.
bAttery InDICAtOr lIGhtS
Green and yellow lights show the
battery condition. The green light
indicates a charged battery. The yellow
light indicates the battery is low
and needs recharging. The red light
indicates the AC charger is connected
and charging.
If the battery is drained after the green
light is off, the life of the battery may
be shortened.
bAttery InDICAtOr lIGhtS
Do not leave the
inflator unattended
while the unit is running.
The universal
adapter must
be locked to secure the inflation
accessories. Any misuse could cause
property damage or personal injury. Use
extreme caution when using inflation
accessories.
Green yellOW reD
lIGht lIGht lIGht
ON OFF OFF
ON ON OFF
OFF ON OFF
OFF OFF ON
www.chpower.com
cool for 20 minutes after 20 minutes
of continuous operation. If not cooled
properly the inflator will overheat.
touches the core of tire valve stem.
After the battery is charged, the inflator
is ready for use. If the battery has not
been charged, see sections 120-VOLT AC
CHARGING or 12-VOLT DC CHARGING
before continuing.
tIreS
1) Turn POWER switch ON (see Figure
1).
Battery Status
Power
Charge
Fuse
figure 1
2) a.) Remove the valve stem cap.
b.) Attach the universal adapter from
the air inflator to the valve stem
with the lever in the up position.
c.) Press the universal adapter down
over the valve stem threads
completely.
d.) Press locking lever down to lock
onto valve stem (see Figure 2).
while the unit is running.
3) Turn COMPRESSOR switch on.
gauge to check the actual pressure in
tires.
bAttery
InDICAtIOn
Full to Normal
Weak-Needs Recharging
Exhausted-Needs Recharging IMMEDIATELY
AC charger connected
Turn unit OFF to
allow inflator to
Make sure the
universal adapter
4) To restart the inflator turn
InflAtAbleS:
1) To use inflation accessories, insert
Compressor
2) Insert the appropriate inflation
12V
Outlet
3) Turn ON POWER and COMPRESSOR
4) When the object is firm, turn the
gauge to check the actual pressure in
inflatable.
12-VOlt DC pOWer SUpply
The inflator can supply power to 12-volt
DC items rated under 10 amps by simply
inserting the item's plug into the 12-volt
DC output socket. Do not attempt to
connect items exceeding the 10 amp,
12-volt rating.
fUSe replACement
When replacing the fuse, make sure
Do not leave the
inflator unattended
the inflator is turned OFF and nothing
is connected to the inflator. A spare 10
amp fuse is supplied with the inflator
(See "Specifications and Features" sheet
Always use a
for location of fuse). neVer replace a
separate pressure
blown fuse with a fuse having a higher
rating.
12-VOlt DC reChArGInG ADApter
fuse replacement
1) Unscrew end of plug counter-
2) If fuse is blown, replace with a new
2
Locking
Lever - push
down to lock
onto valve
stem
figure 2
COMPRESSOR switch off and then
on again.
accessory into the universal adapter
and push the lever to lock into place
(see figure 2). The inflation accessory
will fit securely.
accessory into the inflatable object.
switch.
inflator OFF. DO NOT OVER-INFLATE
OBJECT.
Always use a
separate pressure
clockwise to remove fuse.
10 amp fuse. Always replace a blown
fuse with the same size fuse.
Universal
Adapter
Valve Stem