Table of Contents
Advertisement
Installation Instructions
Installation Instructions
Bendix
BlindSpotter
™
13
12
11
10
9
Installation Kit Contents
Item
Description
No.
1
Radar Sensor Mounting Bracket
Radar Sensor Mounting Screws
2
and Nuts
3
Bendix
BlindSpotter
™
Operator Display Unit Mounting
4
Bracket
BlindSpotter Operator Display Unit
5
(ODU)
6
ODU Mounting Bracket Screws
7
ODU Nuts and Washers
Figure 1 – Bendix
BlindSpotter
™
Side Object Detection System
®
7
6
8
3 ea.
Radar Sensor
®
2 ea.
Installation Kit
®
14
5
Installation Kit Contents (continued)
Item
Qty.
No.
1
8
Heat Shrink Tubing
9
In-Line Splice
10
Solder Sleeve
1
11
Grommet
12
Dielectric Compound
1
BlindSpotter
13
Assembly
1
14
Corrugated Loom
4
4
3
Description
Wiring Harness
®
2
1
Qty.
5
5
5
1
1
1
8 ft.
1
Advertisement
Table of Contents
Related Manuals for BENDIX BlindSpotter
Summary of Contents for BENDIX BlindSpotter
- Page 1 Radar Sensor ™ ® Grommet Operator Display Unit Mounting Dielectric Compound Bracket BlindSpotter Wiring Harness ® BlindSpotter Operator Display Unit Assembly (ODU) Corrugated Loom 8 ft. ODU Mounting Bracket Screws ODU Nuts and Washers 2 ea. Figure 1 – Bendix BlindSpotter Installation Kit ™...
- Page 2 USING A DYNAMOMETER (ODU) is attached to the windshield pillar on the same side are conducted on a vehicle equipped with a Bendix ® as the radar sensor. The ODU warns the driver when one of Wingman system.
- Page 3 10 foot by 24 foot for bus or straight frame sensor. Use the lower two mounting holes as a guide. See truck applications. See Figure 3. Figure 4. NOTE: Bendix does not certify, nor offer warranty on, Bendix BlindSpotter systems where system performance ™...
- Page 4 Mirror 14" (355.6mm) Front of Radar Sensor Minimum Distance 5/16 from 22" Steps and Fuel Tank 48" 18" (558.8mm) (1219.2mm) (457.2mm) Figure 7 – Minimum Installation Clearance adar Sensor Figure 5 – Recommended Location for One R OPERATOR DISPLAY UNIT INSTALLATION See Figure 1.
- Page 5 All wire harness connectors must be properly seated to maintain environmental seals. Push the mating connector until it clicks for a latched seal. Refer to the following steps to install the radar sensor harness. See Figure 10. 1. Insert the harness assembly six-pin connector into the radar sensor.
- Page 6 DISPLAY Operator Display Unit. POWER-UP SYSTEM TEST The ODU indicators display system status at power-up. Refer to the Bendix BlindSpotter Side Object Detection Connector Front System Service Data Sheet SD-61-4933 for system indicators and alert notices during vehicle use. Typical System Indication/Alerts...
- Page 7 Enforcement Bureau; 445 12th Street S.W.; Room 7-C485; Washington, DC 20054. Radar Sensor Substitution Install only radar sensors with recommended service replacements, as provided by Bendix. Contact the Bendix Tech Team at 1-800-AIR-BRAKE (1-800-247-2725), option 2, to request part number assistance.
- Page 8 Figure 18 – Butt Crimp without Heat Shrink Tubing Log-on and Learn from the Best On-line training that's available when you are 24/7/365. Visit www.brake-school.com. S-1657 Rev. 000 © 2017 Bendix Commercial Vehicle Systems LLC, a member of the Knorr-Bremse Group • 05/17 • All Rights Reserved...
Need help?
Do you have a question about the BlindSpotter and is the answer not in the manual?
Questions and answers