Sony TRINITRON KV-28WF1A Service Manual

Be-3d chassis
Hide thumbs Also See for TRINITRON KV-28WF1A:

Advertisement

www.freeservicemanuals.info
SERVICE MANUAL
MODEL
KV-28WF1A
KV-28WF1B
KV-28WF1D
KV-28WF1E
MICROFILM
COMMANDER
DEST.
CHASSIS NO.
RM-839
Italian
SCC-K05Q-A
RM-839
French SCC-K01S-A
RM-839
AEP
SCC-K07T-A
RM-839
Spanish SCC-K06S-A
World of free manuals
MODEL
KV-28WF1K
KV-28WF1R
KV-28WF1U
TRINITRON COLOR TV
— 1 —
KV-28WF1
BE-3D
CHASSIS
COMMANDER
DEST.
RM-839
OIRT
RM-839
OIRT
RM-839
UK
R
6/8/2013
CHASSIS NO.
SCC-K20H-A
SCC-K20G-A
SCC-K04N-A
R

Advertisement

Table of Contents
loading

Summary of Contents for Sony TRINITRON KV-28WF1A

  • Page 1 www.freeservicemanuals.info 6/8/2013 KV-28WF1 SERVICE MANUAL BE-3D CHASSIS MODEL MODEL COMMANDER DEST. COMMANDER DEST. CHASSIS NO. CHASSIS NO. KV-28WF1A RM-839 Italian SCC-K05Q-A KV-28WF1K RM-839 OIRT SCC-K20H-A RM-839 French SCC-K01S-A RM-839 OIRT SCC-K20G-A KV-28WF1B KV-28WF1R RM-839 SCC-K04N-A KV-28WF1D RM-839 SCC-K07T-A KV-28WF1U KV-28WF1E RM-839 Spanish SCC-K06S-A TRINITRON COLOR TV...
  • Page 2 www.freeservicemanuals.info 6/8/2013 KV-28WF1 a i l SPECIFICATIONS Picture Tube Super Trinitron [FRONT] Approx. 71 cm (28 inches) 3 , Video input - phono jack (Approx. 66 cm picture measured 3 , Audio inputs - phono jacks diagonally) 3 , S video input - 4 pin DIN 110°...
  • Page 3 www.freeservicemanuals.info 6/8/2013 KV-28WF1 [RM-839] Remote control system Infrared control Power requirements 3V dc (2 batteries) R6 (size AA) Dimensions Approx. 210x45x24 mm (w/h/d) Weight Approx. 90g (Not including battery) Design and specifications are subject to change without notice. l i o a i l s i l WARNING...
  • Page 4 www.freeservicemanuals.info 6/8/2013 KV-28WF1 21 pin connector ( :2/q2 R/D/D/D-L/G/S/I ) t f ) t f ± v i t ± v i t ± v i t 1 ± v i t 1 ± v i t 1 ± v i t l i e Connected Not Connected (Open)
  • Page 5: Table Of Contents

    APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES PUBLISHED BY SONY. COMPOSANTS SONY DONT LE NUMÉRO DE PIÉCE EST INDIQUÉ DANS LE PRÉSENT MANUEL OU DANS DES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 6 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 7 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 8 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 9 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 10 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 11 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 12 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 13 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 14 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 15 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 16 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 17 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 18 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 19 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 20: Disassembly

    www.freeservicemanuals.info 6/8/2013 SECTION 2 DISASSEMBLY 2-1. REAR COVER REMOVAL 2-2. CHASSIS ASSY REMOVAL Rear Cover Seven screws (BVTP 4x16) 2-3-2. SERVICE POSITION (2) 2-3-1. SERVICE POSITION (1) World of free manuals...
  • Page 21: Wire Dressing

    www.freeservicemanuals.info 6/8/2013 2-4. WIRE DRESSING 2-5. A BOARD REMOVAL A board. 2-6. A EXTENSION BOARD A board BE-3D EXTENSION BOARD World of free manuals...
  • Page 22: Picture Tube Removal

    www.freeservicemanuals.info 6/8/2013 2-7. PICTURE TUBE REMOVAL • REMOVAL OF ANODE-CAP Note: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT, after removing the anode. Two DGC holers * REMOVING PROCEDURES.
  • Page 23: Removal And Replacement Of The Main-Bracket

    www.freeservicemanuals.info 6/8/2013 REMOVAL AND REPLACEMENT OF THE MAIN-BRACKET For safety reasons, on no account should the plates be removed BOTTOM PLATES. and not refitted after servicing. (1) REMOVING THE PLATES (2) REFITTING THE PLATES Because the plates differ in size it is important that the correct plates are refitted in their In the event of servicing being required to the solder side of the D Board printed original location.
  • Page 24: Set-Up Adjustments

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 SECTION 3 SET-UP ADJUSTMENTS • • When complete readjustment is necessary or a new Carry out the following adjustments in this order : picture tube is installed, carry out the following 1. Beam landing adjustments. 2. Convergence •...
  • Page 25: Convergence

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 3-2. CONVERGENCE Preparation: • Tilt the V.STAT magnet and adjust the static • Before starting this adjustment, adjust the focus, convergence by opening or closing the V.STAT magnet. horizontal size, and vertical size. • Minimize the brightness setting. •...
  • Page 26 www.freeservicemanuals.info 6/8/2013 KV-28WF1 • Operation of BMC (Hexapole) Magnet V.STAT Purity BMC (Hexapole) • The respective dot position resulting from moving each magnet interact, so be sure to perform adjustment while tracking. Use the H.STAT VR to adjust the red, green, and blue dots so they coincide at the centre of the screen (by moving the dots in the horizontal direction).
  • Page 27: White Balance

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 3-3. WHITE BALANCE (3) Screen corner convergence. If you are unable to adjust the corner convergence properly, G2 Setting correct them with the use of permalloy assemblies. 1. Switch the set into AV mode (apply no signal to the AV connectors).
  • Page 28: Circuit Adjustments

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 SECTION 4 CIRCUIT ADJUSTMENTS 4-1. ELECTRICAL ADJUSTMENTS PICTURE ADJUSTMENT Service adjustment to this model can be performed AFC mode with the supplied remote commander RM-862. REF position HOW TO ENTER INTO SERVICE MODE SCP BGR SCP BGF 1.
  • Page 29 www.freeservicemanuals.info 6/8/2013 KV-28WF1 SUB BRIGHTNESS ADJUSTMENT AGC ON/OFF 1. Input a Phillips pattern. Constant gain CDB 2. Set the picture control to minimum. FM prescale FMP 3. Enter into the Picture Adjustment Service Menu. Zwei mono-st WHI 4. Adjust the Sub-Brightness data so that there is barely a Zwei st-mono WLO difference between the 0 IRE and 10 IRE signal.
  • Page 30 www.freeservicemanuals.info 6/8/2013 KV-28WF1 SYSTEM B/G, D/K, I & L I.F ADJUSTMENT DEFLECTION SYSTEM ADJUSTMENT 1. Input an off air signal of between 60-100dBuV / 75 ohm 1. Enter into the Geometry Adjustment Service Menu. terminated, via the tuner socket. 2. Select and adjust each item in order to obtain the optimum 2.
  • Page 31: Test Mode

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 4-2. TEST MODE 2: Is available by pressing Test button twice, OSD " TT " appears. The functions described below are available by pressing the two numbers. To release the Test mode 2, press 0 twice, or switch the TV into stand-by mode. Note: TT modes 40-49 require the TV to be in programme 59 before the command is accepted.
  • Page 32 www.freeservicemanuals.info 6/8/2013 KV-28WF1 i t s i t s t i s t l i f t l i f y t i y t i t i s t i s t i s t i s These test modes can set the delay byte to any value 0-31 t i s which creates a (value x 20) mS delay.
  • Page 33: Be-3D Self Diagnostic Software

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 4-3. BE-3D SELF DIAGNOSTIC SOFTWARE The identification of errors within the BE-3D chassis is triggered in 1 of 2 ways :- 1: Bus busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
  • Page 34 www.freeservicemanuals.info 6/8/2013 T803 FBT D901 RES STBY 5V Q900 IC500 D810 V OUT TO PICTURE 200V RECT 200V TUBE SWITCH RESP Q501 SIRCS D505 D504 135V -15V D507 +15V TO C BOARD IC900 FBT —15V D803 J701 (G4) INFRARED RECEIVER SWITCH SWITCH D502...
  • Page 35 www.freeservicemanuals.info 6/8/2013 T803 FBT D901 RES STBY 5V Q900 IC500 D810 V OUT TO PICTURE 200V RECT 200V TUBE SWITCH RESP Q501 SIRCS D505 D504 135V -15V D507 +15V TO C BOARD IC900 FBT —15V D803 J701 (G4) INFRARED RECEIVER SWITCH SWITCH D502...
  • Page 36 www.freeservicemanuals.info 6/8/2013 WAVEFORMS C BOARD 110 Vp-p (H) 108 Vp-p (H) 90 Vp-p (2H) 21 Vp-p (2H) WAVEFORMS D BOARD 1.2K Vp-p (H) 56.0 Vp-p (V) 13.0 Vp-p (H) 178 Vp-p (H) 2.6 Vp-p (H) 56 Vp-p (V) 31 Vp-p (V) 140 Vp-p (H) 3.9 Vp-p (H) 1.0 Vp-p (H)
  • Page 37 www.freeservicemanuals.info 6/8/2013 A BOARD IC301 CXA2000Q-TL A BOARD IC4 PST593C H SYNC PHASE 32fH V SYNC PHASE PHASE GATE H.DRIVE 1/32 SHIFT SAND CASTLE DELAY V out SHARP D PIC 50/60 ID TRAN VIDEO NESS TRAP CONT WIDE Count Down Sawtooth GATE 525/625...
  • Page 38 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 39 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 40 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 41 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 42 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 43 www.freeservicemanuals.info 6/8/2013 World of free manuals...
  • Page 44 www.freeservicemanuals.info 6/8/2013 KV-28WF1 5-4. SEMICONDUCTORS CXA2040Q-T4 MSP3400C-PS-C6-T STR-S6708 BF871-127 MSP3410B-PS-F7-T BF421L-AMMO (TOP VIEW) JA101TP-Q ( TOP VIEW ) 2SA733-K L4941BV 2SA933AS TEA7605 2SA933S PST593C-MMP-4P 2SA1091-O STV9379 2SC3502-E 2SC3601-E 2SC2808STP-R ( TOP VIEW ) E C B LM393P M5216P SBX1790-51 DTA144ES TDA2822M µPC393C DTC114ES...
  • Page 45 www.freeservicemanuals.info 6/8/2013 KV-28WF1 FML-G12S RD3.9ESB2 TLP721(D4-) AU-01Z-V1 MTZJ-3.6A EG-1Z-V1 GP08D RD5.1ESB2 MTZJ-3.9B RD5.6ESB2 EGP20G RGP02 MTZJ-5.1B RD6.2ESB2 EL1Z RGP10GPKG23 MTZJ-5.6B RGP15GPKG23 RD6.8ESB2 EM1-V1 MTZJ-6.2B RU3YX-V1 RD7.5ESB2 EU-1-V1 MTZJ-6.8B RD10ESB2 EU2A RU4AM-T3 MTZJ-7.5C RD39ES-B2 EU2-V1 RU4DS MTZJ-9.1 MTZJ-T-77-9.1A MTZJ-10 1SS133T-77 2SC2785-HFE MTZJ-39 CATHODE CATHODE...
  • Page 46: D2 Board

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 SECTION 6 EXPLODED VIEWS NOTE : • Items with no part number and no description are not stocked because they The components identified by Les composants identifies par une are seldom required for routine service. shading and marked are critical trame et une marque sont...
  • Page 47: Picture Tube

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 6-2. PICTURE TUBE Les composants identifies par une The components identified by shading and marked are critical trame et une marque sont for safety. critiques pour la securite. Ne les remplacer que par une piece Replace only with the part number specified.
  • Page 48: Electrical Parts List

    www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. SECTION 7 Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 49 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 50 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 51 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 52 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 53 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece KV-28WFA/28WFD/28WF1E/ specified.
  • Page 54 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece IF ( specified.
  • Page 55 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 56 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 57 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 58 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 59 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 60 www.freeservicemanuals.info 6/8/2013 KV-28WF1 The components identified by Les composants identifies par shading and marked are critical une trame et une marque sont for safety. critiques pour la securite. Replace only with the part number Ne les remplacer que par une piece specified.
  • Page 61 Ne les remplacer que par une piece specified. portant le numero specifie. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK Sony Corporation English Sony UK 97GP7187-1 Service Promotions Div. 9-974-957-01 Printed in U.K. © 1997.7 — 86 — World of free manuals...

Table of Contents