Table of Contents
Advertisement
Quick Links
R
e
m
o
t
e
K
e
y
p
R
e
m
o
t
e
K
e
y
p
I
d
e
n
t
i
f
y
i
n
g
t
I
d
e
n
t
i
f
y
i
n
g
t
Green Active LED
1
2
Red TX LED
3
Orange Fault LED
4
Slide Out Section
5
Arm Key
6
Home Key
Χ Key
7
8
Disarm Key
9
＃ Key
Key
L
E
D
I
n
d
i
c
a
t
o
L
E
D
I
n
d
i
c
a
t
o
G
r
e
e
n
A
c
t
i
G
r
e
e
n
A
c
t
i
Green Active LED on: the system is in Normal Operation Mode.
Green Active LED flash: the system is in Test Mode.
When the Keypad is idle, all LEDs are off. After any key press, the
seconds indicating that Keypad is active.
T
T
h
h
e
e
G
G
when the pause in between key stokes is longer than 5 seconds.
When the
the previous entered keys are ignored.
R
e
d
T
X
L
E
R
e
d
T
X
L
E
The Red TX LED flashes 2 times: the signal is transmitted.
O
r
a
n
g
e
F
a
O
r
a
n
g
e
F
a
Orange Fault LED flashes for 5 times: Battery is low during operation.
<
N
O
T
E
>
<
N
O
T
E
>
A short beep will be sounded with each key press, which confirms valid pressing.
a
d
(
K
P
-
1
5
/
K
a
d
(
K
P
-
1
5
/
K
h
e
P
a
r
t
s
:
h
e
P
a
r
t
s
:
r
:
r
:
v
e
L
E
D
:
v
e
L
E
D
:
r
r
e
e
e
e
n Active LED will turn off after successful completion of a valid keystroke sequence or
n
G
r
e
e
n Active LED turns off before a valid keystroke sequence is completed (5 seconds),
G
r
e
e
n
D
:
D
:
u
l
t
L
E
D
:
u
l
t
L
E
D
:
P
A
-
1
5
)
P
A
-
1
5
)
+ Key
-press both 7 and 9 to trigger emergency alarm
Fire Key
-press both 4 and 6 to trigger fire alarm
A Key
-press both 1 and 3 to trigger panic alarm
Mounting Hole
Buzzer
Battery Insulator
1
2
1
-
D
2
1
-
G
r
e
e
n Active LED turns on for 5
G
r
e
e
n
E
C
-
2
0
0
9
D
E
C
-
2
0
0
9
Advertisement
Table of Contents
Related Manuals for Climax KP-15
Summary of Contents for Climax KP-15
- Page 1 + Key Green Active LED -press both 7 and 9 to trigger emergency alarm Red TX LED Fire Key Orange Fault LED -press both 4 and 6 to trigger fire alarm Slide Out Section A Key Arm Key -press both 1 and 3 to trigger panic alarm Home Key Mounting Hole Χ...
- Page 2 4 continuous beeps will sound indicating the user that he has entered invalid keystroke, and the user is asked to repeat the process again. The Keypad uses a CR2450 3V 540mAH lithium battery as its power source. It has a typical battery life of over 7 years at an average of 4 activations a day.
- Page 3 Step 1. Put Keypad in Test mode by entering “0000” (default PIN code), then press ＊. Keypad will sound 1 long beep and the Green Active LED will steadily flash. Step 2. Adding Keypad into the Control Panel: I. Put the Control panel into Device +/- menu and select the Add Devices sub menu. II.
- Page 4 Enter Test Mode — Enter Keypad PIN code and press ＊ key. The Keypad will sound 1 long beep and Green Active LED flashes steadily. Panic Alarm — Press 1 + 3 simultaneously at the same time. Red TX LED will flash 5 times and the Keypad sounds a long beep.
- Page 5 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Need help?
Do you have a question about the KP-15 and is the answer not in the manual?
Questions and answers