MORDOMUS Slim Multisensor iZSL-1 Manual

Advertisement

Slim Multisensor iZSL-1/2/7
The slim multisensor iZSL has PIR, door/window, temperature and
illumination, 4 sensors function in one, based on Z-Wave
It is the Z-Wave
TM
plus product, it support the security, OTA... Those
newest features of the Z-Wave
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
TM
technology.
TM
technology. Z-Wave
TM
is a wireless
TM
500 series chip, when your Z-Wave
TM
500 series devices. The
Concurrent multi-channel support reduces external interference.
Better RF range, improve about 10 meters in indoor.
Support 100 Kbps transmit speed, speed up communication.
Function Compare 1/2/7
iZSL-1
iZSL-2
iZSL-7
Add to/Remove from Z-Wave
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-Wave
In the first time, add the device into the Z-Wave
sure the primary controller is in the add mode. And then power on the
device, just take out the insulation Mylar in the back side of the device.
The device will auto start the NWI (Network Wide Inclusion) mode. And
it should be included in 5 seconds. You will see the LED light ON one
second.
TM
network
Notice: Including a node ID allocated by Z-Wave
"Add" or "Inclusion". Excluding a node ID allocated by Z-Wave
Controller means "Remove" or "Exclusion".
TM
1
www.mordomus.com
PIR
Temperature Illumination
Door/Window
V
V
V
V
TM
Network
TM
network.
TM
V
V
V
V
V
V
network. First, make
TM
Controller means
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Slim Multisensor iZSL-1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MORDOMUS Slim Multisensor iZSL-1

  • Page 1 Slim Multisensor iZSL-1/2/7 Concurrent multi-channel support reduces external interference. • Better RF range, improve about 10 meters in indoor. • Support 100 Kbps transmit speed, speed up communication. • Function Compare 1/2/7 Temperature Illumination Door/Window iZSL-1 iZSL-2 iZSL-7 Add to/Remove from Z-Wave...
  • Page 2: Function Description

    The group 2 is for light control, the device will send the “Basic Set” command to this group. And each group support 8 nodes maximum. Failed or success in add/remove the node ID can be viewed • www.mordomus.com...
  • Page 3: Over The Air (Ota) Firmware Update

    Caution: After remove the battery, please wait about 30 seconds, and then re-install the battery. Replace the new battery and install the cover back. 1. Put the front cover bottom to 1-1, and press down. 2. Push the front cover top to 2-1. www.mordomus.com...
  • Page 4: Installation

    Choosing a Suitable Location 1. The recommended mounting height is 160cm 2. Don't let the device facing the window or the sunlight. 3. Don't let the device facing the source of heat. For instance the heater or the air-condition. www.mordomus.com...
  • Page 5: Specifications

    * The reserve bit or not supported bit is allowed any value, but no effect. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material www.mordomus.com...
  • Page 6: Fcc Interference Statement

    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. www.mordomus.com...

This manual is also suitable for:

Slim multisensor izsl-2Slim multisensor izsl-7

Table of Contents