Advertisement
Quick Links
GPS TRACKER USER
MANUAL
PREFACE
Thank you for purchasing GPS tracker. This manual shows how to operate the device
smoothly in details, please make sure to read this manual carefully before using the device.
Please be noted that any update of the manual is made without prior notice. Each time the
update of the manual will be released in the latest product sales. The manufacturer won't
assume any legal responsibility for any errors or omissions made in this manual.
Advertisement
Related Manuals for Accurate Technology GT06AB
Summary of Contents for Accurate Technology GT06AB
- Page 1 GPS TRACKER USER MANUAL PREFACE Thank you for purchasing GPS tracker. This manual shows how to operate the device smoothly in details, please make sure to read this manual carefully before using the device. Please be noted that any update of the manual is made without prior notice. Each time the update of the manual will be released in the latest product sales.
- Page 2 1 SUMMARY Working based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS, APP and Internet. It adopts the most advanced technology of GPS and AGPS dual positioning. Content Specs. Dim. 95*50*13mm Weight Network...
- Page 3 2.1) device front side towards the sky. When install in car, if the windscreen glued by metal thermal insulation layer or heating layer, it will reduce the GPS receive signal and lead to GPS work disorder.
- Page 4 (The GPS tracker must be installed professional personnel) 2.2 Wires connection 2.2 device power wire connection as below: 2.2.1 Red wire connects to vehicle power positive + 2.2.2 Black wire connects to vehicle power negative - 2.2.3Yellow wire connects to relay yellow wire 2.2.4 Green wire connects to ACC wire 2.25 thin Red wire connects to the door control circuit if it is positive 2.26 thin black wire connects to the door control circuit if it is negative...
-
Page 5: Indicator Light Status
INDICATOR LIGHT STATUS MEANING green light -Solid GSM signal connection green light -Flash NO GSM connection Blue light -Solid GPS signal connection Blue light -Flash No GPS or searching gps signal Note: All ledS will turn off after 5 minutes for best hide Connect 12V-36 v voltage of the power supply 3. -
Page 6: Turn On The Device
· SOS alarm ; · Built-in backup battery to realize power failure alarm; · Cut vehicle oil or circuit (optional). · Add Open the door alarm; · Add Vibation alarm · Add Smart sleep save power Mode 4. Notices: 1.GPS tracking can be worked outdoor. 2.Please make sure GSM SIM card(2G GSM network or compatibility 2G GSM network) supports making calls, sending messages, GPRS network. - Page 7 The device gets GPS location when there is GPS signal and gets LBS location when there is no GPS signal. The device automatically turns off when the SIM card is removed. 6.SMS TRACKING(123456 is default password) 6.1. insert the SIM card, take device to outdoor 6.2.
- Page 8 number.（13800138000） Admin number Canceling: ：noadmin123456 13800138000 Command Reply：noadmin ok 6.4 Monitor 6.4.1 The default mode is “tracker” (Tracker mode). 6.4.2 Send SMS “monitor+password” to the unit,switch to “monitor” mode.then use your mobile call the device sim card,unit will auto pick 6.4.3 Cancel monitor Send SMS “tracker+password”...
- Page 9 6.6 Cut off the Oil and Power System 6.6.1 Send command “cut+password” to tracker,And it will remain immobile state until next command to resume.it will be executed , and stop the car when the speed is less than 20KM/H. 6.6.2 resume the Oil and Power System Send “resume+password"...
- Page 10 Send “shock+password+space+level” to the unit(level from 1 to 5,1 is the highest sensitive),when the sensor is striggered ,and will send send Vibrate alarm+latitude&longitude”, 6.9.1 6.9.2 canceling: Send SMS “noshock+password” 7. Arm set 7.1.1 Send SMS command “arm+password” to the tracker. the SMS command will make the tracker device enter into armed state,User must stop the engine, (that is ACC is lower voltage),You will set up arm status fail if the engine is turned on (the ACC is high voltage), it will reply “set up fail! pls turn off ACC”...
- Page 11 Send SMS command "disarm + password" to the tracker device, and the SMS command will make the tracker device enter into disarmed state. Alarms under Arm State 7.1.2 Door open alarm The unit will send SMS “Door alarm+lat/long” to the authorized number at interval of every 3 minutes when the door of the car always open in arm status.
- Page 12 7.2 Over-speed Alarm setting（It works only in continuous positioning mode.） Over-speed Alarm setting: ：speed123456 Command 70（Suppose speed is 70km/h）note: not less 60KM/H Reply：speed ok E.g： When the unit speed is over 70km/h, it will send message “speed alarm!” to the admin number .
- Page 13 7.5 Reset Hardware Command：reset123456 Reply：reset ok 7.6 Change the password Command: password123456 888888 Reply :password OK Note: 123456 is the old password(default ),888888 is the new password,it must the 6 digits Arabic numerals 7.8 Smart sleep save power Mode SMS Mode(close GPRS Mode GPRS) Normal...
- Page 14 and sms command can awake it. 7.8.1 send “sleepin+password” 7.8.2 Cancel: Send “sleepout+password”, tracker will reply “sleepout ok”, tracker won’t sleep, GSM and GPS works all the time. 7.8.3 switch GPRS to SMS mode (SMS mode means close the GPRS) The default mode is “GPRS”, Send SMS “sms+password”...
- Page 15 Lat:22.039124 lon:114.039124 Positioning of the latitude and longitude values. Spd：000 This refers to the device moving speed. The unit is km/h. Time:18/15/43 real-tracking time, the Default is beijing time. You can set a time zone by sms command Google Link: This is the link to the Google map showing the position of the device.
- Page 16 A more open view of the sky is recommended to make No GPS sure the device can receive the GPS signal normally.in No reply to SMS Password wrong or the format is wrong. command No reply to calling & Authorized / admin phone number is incorrect or has not SMS position OK, Pls check if APN is correctly set.