About The Remote Control; Loading The Batteries; Using A Remote Control; Changing The Signal Code Of A Remote Control - Marantz BD8002 User Manual

Introduction Introduction
About the Remote Control
I
Using a Remote Control
I
Changing the Signal Code of a Remote Control
• Change the signal code of the remote control
Setto"B01":
Press hold down both. and [1) on the remote control for at least
five seconds.
Set to "B02":
Press hold down both. and [2) on the remote control for at least
five seconds.
6) Press [SETUP) to exit.
• At this point the new signal code of the unit is effective. Please
change the signal code of the remote control to match to the
signal code of the unit with following procedure.
• Change the signal code of the unit
1) In stop mode, press [SETUP).
2) Use
[<J It»
to select. then press [ENTER).
3) Use
[<J
It»
to select. then press [ENTER).
4) Use
[~I
V) to select "Remote Control Setting".
S) Press [ENTER) to select "B01" or "B02".
To avoid the other Marantz's BD players responding the remote
signal of this unit, you can change the signal code of the remote
control. If the signal code of the remote control does not match to
the signal code of the unit, you cannot control the unit with the
remote control.
• Ifthe signal code does not match, the signal code of the remote
control will be displayed on the front panel display.
• The default setting and the setting after you change the
batteries is "BD1 ".
16
feet
(Sm) 30· 16
feet
(Sm) 16
feet
(Sm) 30·
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the remote
control and infrared sensor window on the unit.
• Remote operation may become unreliable if strong sunlight or
fluorescent light is shining on infrared sensor window of the
unit.
• Remote control for different devices can interfere with each
other. Avoid using remote control for other equipment located
close to the unit.
• Replace the batteries when you notice a fall off in the operating
range of the remote control.
• The maximum operable ranges from the unit are as follows.
- Line of sight: approx. 16 feet (Sm)
- Either side of the center: approx. 16 feet (Sm) within 3D·
®
Insert two "AA" (R6P)
batteries, with each one
oriented correctly.
CD
Open the battery
compartment cover.
®
Close the cover.
"". ,<'}llL
~
l'F
1: 1 , '
'*'}
rlF"'S,;:,,,,..
ffWi'
'1%
"or:
,,'autions
on BClfte~
, • ". '"
;J~trus~
"M." (R6PY batteries
JO,..
cdnttoJ.:
';'I ..
~
•
~::Ef
",
>:dfd;;;.,tn:;c ,::
~
- I'
'. Rtlplace the batt.eriesWith,i1eWones approximately"once a
'iii
year,.though this d~~r:KIsrofi'thefrequen~ with :whidit~e,~,
remote control IS
used.~'
. .
' l ' : ,
.If
the remote control dpes not-oP,erate wi!hin a close, . ,
prqxiiDJty of the main unit;--reQlace the batteries with hew'- -
one.s, eVen if less than a year bas passed. .
• The included batteries s~rve only for'verifying operation.
- - Replace them With·new !>atteries as soon as possible.
•• When inserting the batteries, be careful to do so in the
proper direction, folloWing the EB and
e
marks in the remote
, control's battery compartm.ent•.
• To prevent damage or battery fluid leakage:
- Do not mix a new battery with an old one.
- Do not mix two different-types ofbatteries'Such as alkaline
<
and manganese.'="- .: _
w
- Do not short-eircuit,djsas-s~mbie, heat or dispose of
'."
batteries in
f1ame~,.
.
":~
_., . .
~
.~
RemQve the batteries wheri.not planning to use the-remote
· Eo,ntrol for a long periqd of
~Jne,'
' . . ' , ';,
,-
Ihhe.batterie~
shQuld
I~al<,.c~r~ullywipe,
off.the fluid
"jhe
insl~e
of tl'le battery.c . rtment, then Insert
t batteries,:'
·i., . -~_-
-i";'"
'~ii_',
<>,l1';'-r
-:<1:.':t
{I+
I
Loading the Batteries
6
ENGLISH