Page 1
Operator's Manual WARNING! Read this operator’s manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire and/or serious personal injury.
Table of Contents RECORDING FORM FOR MACHINE SERIAL NUMBER .................... 1 SAFETY SYMBOLS ..............................2 GENERAL SAFETY RULES ............................2 ..............................2 AFETY ..............................2 LECTRICAL AFETY ..............................3 ERSONAL AFETY ............................3 QUIPMENT SE AND ............................ 3 ATTERY AND CHARGER SAFETY ..................................
Safety Symbols In this operator’s manual safety symbols and signal words are used to communicate important safety information. This section is provided to improve understanding of these signal words and symbols. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Personal Safety equipment. Accessories that may be suitable for one piece of equipment may become Stay alert, watch what you are doing and hazardous when used with other equipment. common sense when operating Keep handles dry and clean; free from oil equipment.
AC power supply. When hand injuries. Only wear latex or rubber gloves powered by battery it is considered portable, under RIDGID Drain Cleaner Gloves. Do not therefore when used, it shall be protected from use damaged drain cleaning gloves.
32708 32713 Single Battery Kit with Charger RIDGID Scout or the Navitrack II). A Ridgid transmitter (such as the SeekTech The LCDPak Pak is protected under U.S. and ST-510, the SeekTech ST-305, the SeekTech international patents. ST-33Q, the Navitrack Brick or the Navitrack 10-watt transmitter).
Brightness Key LCDPak Components Sonde Key Power Key Monitor Accessory Interface Port SeeSnake Zero Key System Connector Transmitter Clip‐ on Terminal Video Out Figure 2: Front View (Open) and Controls External Power Cord Front Cover Serial # Label Optional Batteries Front Cover Release Button Figure 3: Front View (Closed) Figure 4: Rear View Ridge Tool Company...
Ridge Tool Catalog, online www.RIDGID.com or www.RIDGID.eu. 4. Make sure all equipment has been properly inspected. 5. Evaluate the work area and determine if any barriers are needed to keep bystanders away. Bystanders can distract the operator during use.
lower position. Press cover into place until it 6. If needed, remove fixture (water closet, sink, locks. etc.) to allow access. Set up the LCDPak so its monitor screen is easy to see and its controls are easy to reach during use. In brightly LCDPak Placement lit areas, point the monitor screen away from bright light Place the LCDPak to allow easy access and viewing...
Powering The SeeSnake LCDPak The SeeSnake LCDPak can either be powered with RIDGID Li-Ion rechargeable battery or plugged in to an outlet using a supplied AC/DC power converter. Battery power is the preferred powering method to reduce the risk of electrical shock.
Power Key Sonde Key Brightness Key Operating Instructions WARNING Always wear eye protection to protect your eyes against dirt and other foreign objects. When inspecting drains that might contain hazardous Zero Key chemicals or bacteria, wear appropriate protective Figure 9: LCDPak Controls equipment, such as latex gloves, goggles, face shields or respirators, to prevent burns and infections.
SeeSnake push rod underground, using and then decrease it until it reaches minimum. a standard RIDGID locator such as the NaviTrack® II, The Brightness LED next to the Brightness Key the Scout™, the SeekTech SR-20 or the SeekTech indicates the level of brightness by blinking.
Maintenance Instructions Cleaning WARNING Make sure all cords and cables are disconnected and the battery removed prior to cleaning the LCDPak to reduce the risk of electrical shock. Do not use liquid or abrasive cleaners on the LCDPak. Clean the LCDPak with damp cloth. Only use cleaners Figure 11: Line Tracing the Pushrod approved for use on LCD screens to clean the screens.
(including RIDGID®, and other battery suppliers have developed amplifiers) that produce heat. programs in the USA and Canada to collect and recycle rechargeable batteries. Normal rechargeable batteries contain materials that should Service and Repair not be directly disposed of in nature, and contain valuable materials that can be recycled.
Chart 1 Troubleshooting PROBABLE FAULT PROBLEM SOLUTION LOCATION Check power is correctly plugged in. No power to SeeSnake connector. Check switch on LCDPak monitor. Check alignment and pins of connection to LCDPak unit from SeeSnake. Connections faulty. Camera video image Check orientation, seating, and pin condition in the not seen.
Page 17
RIDGID® tools are warranted to be free of defects in workmanship and material. How long coverage lasts This warranty lasts for the lifetime of the RIDGID® tool. Warranty coverage ends when the product becomes unusable for reasons other than defects in workmanship or material.