Advertisement
Quick Links
Fisher Engineering
50 Gordon Drive, Rockland, Maine 04841-2139 • www.fi sherplows.com
7'6" EZ-V
Installation Instructions
Read this document before installing the
snowplow.
See your FISHER
®
vehicle application recommendations before
installation. The eMatch selection system has
specifi c vehicle and snowplow requirements.
A DIVISION OF FISHER, LLC
95150, 95160, 95180-3, 95190-3
Snowplow
®
CAUTION
CAUTION
outlet/website for specifi c
August 1, 2020
Lit. No. 74916, Rev. 02
Advertisement
Related Manuals for Fisher Minute Mount 2 EZ-V 95150
Summary of Contents for Fisher Minute Mount 2 EZ-V 95150
- Page 1 Installation Instructions CAUTION Read this document before installing the snowplow. CAUTION See your FISHER outlet/website for specifi c ® vehicle application recommendations before installation. The eMatch selection system has specifi c vehicle and snowplow requirements. A DIVISION OF FISHER, LLC...
- Page 2 95150, 95160, 95180-3, 95190-3 SAFETY DEFINITIONS WARNING/CAUTION AND INSTRUCTION LABELS WARNING Become familiar with and inform users about the Indicates a potentially hazardous situation warning labels on the back of the blade and the that, if not avoided, could result in death or instruction label on the headgear.
- Page 3 WARNING FUSES The driver shall keep bystanders clear of the The FISHER ® electrical and hydraulic systems blade when it is being raised, lowered, or contain several automotive-style fuses. If a problem angled. Do not stand between vehicle and should occur and fuse replacement is necessary, blade or within 8 feet of a moving blade.
- Page 4 95150, 95160, 95180-3, 95190-3 FIRE AND EXPLOSION BATTERY SAFETY WARNING CAUTION Gasoline is highly fl ammable and gasoline Batteries normally produce explosive gases, vapor is explosive. Never smoke while which can cause personal injury. Therefore, working on vehicle. Keep all open fl ames do not allow fl...
- Page 5 95150, 95160, 95180-3, 95190-3 TORQUE CHART HEADGEAR TO T-FRAME ASSEMBLY NOTE: For easier assembly and installation, the CAUTION vehicle and all snowplow components should Read instructions before assembling. be on a smooth, level, hard surface, such as Fasteners should be fi nger tight until concrete.
- Page 6 95150, 95160, 95180-3, 95190-3 3. Remove the hardware and blocking that secures the T-frame to the pallet. 4. Remove the strapping that secures the headgear to the T-frame. 5. While supporting the headgear, remove the self- tapping screw from each shipping bracket and discard.
- Page 7 95150, 95160, 95180-3, 95190-3 T-FRAME TO BLADE ASSEMBLY 5. Remove the protective packaging from the angle rams. 1. Remove the blade wings from the metal shipping 6. Align the holes in the rod ends of each angle ram brackets. Discard the shipping brackets and with the corresponding holes on the back of the replace the cutting edge hardware.
- Page 8 95150, 95160, 95180-3, 95190-3 HEADLAMPS 6. Secure the snowplow harnesses and wires to the headgear with cable ties as shown. WARNING Cable Ties Your vehicle must be equipped with snowplow headlamps and directional lights. Headlamps, hardware, and instructions are found in Snowplow the headlamp box.
- Page 9 Pipe retracted, the fl uid level should reach the fi ll hole. Plug If additional fl uid is needed, fi ll the reservoir with FISHER ® EZ Flow Hydraulic Fluid rated to –40°F (–40°C), or other fl uid conforming to...
- Page 10 95150, 95160, 95180-3, 95190-3 BLADE DROP SPEED ADJUSTMENT WARNING Keep 8' clear of the blade when it is being raised, lowered, or angled. Do not stand between the vehicle and the blade or directly in front of the blade. If the blade hits or drops on you, you could be seriously injured.
- Page 11 95150, 95160, 95180-3, 95190-3 FINAL ADJUSTMENTS 2. Remove and retain the U-bolt and locknuts that secure the lift chain on the passenger's side of the T-frame. Reposition the U-bolt in the chain so that WARNING the chain is the same length as the chain on the driver's side.
- Page 12 95150, 95160, 95180-3, 95190-3 Adjusting the Lift Chain Spring Lift Chain (DS) The lift chain spring ensures proper operation of the snowplow mounting system by providing slack in the lift chain after the blade is lowered. Connecting Chain Link The EZ-V 7'6"...
- Page 13 95150, 95160, 95180-3, 95190-3 Adjusting the Center Cutting Edges Lubricating the Pivot Pin Hinge The center cutting edge spacer plate is located on the Using a rubber-tipped seal-off coupler fi tting, apply a T-frame below the pivot pin hinge. good quality multipurpose grease at the fi ve grease points along the center hinge of the blade.
- Page 14 95150, 95160, 95180-3, 95190-3 VEHICLE LIGHTING CHECK With headlamp switch OFF, activate the vehicle DRLs. 1. Verify the operation of all vehicle front lighting Snowplow lighting harness DISCONNECTED: prior to connecting the snowplow harness. • Vehicle DRLs should be ON. •...
- Page 15 95150, 95160, 95180-3, 95190-3 OWNER'S MANUAL PACKET If the completed snowplow will be delivered immediately, the Owner's Manual should be reviewed with and given to the purchaser according to the snowplow checklist. If the snowplow is completed prior to delivery to the purchaser, attach the Owner's Manual packet to the electrical cable of the cab control for safekeeping.
- Page 16 Fisher Engineering or the vehicle manufacturer may require or recommend optional equipment for snow removal. Do not exceed vehicle ratings with a snowplow. Fisher Engineering off ers a limited warranty for all snowplows and accessories.
Need help?
Do you have a question about the Minute Mount 2 EZ-V 95150 and is the answer not in the manual?
Questions and answers