Download  Print this page

Sharp SDW6757ES Installation Manual

Hide thumbs

Advertisement

Quick Links

BEFORE YOU BEGIN READ THESE
INSTRUCTIONS COMPLETELY AND
CAREFULLY.
IMPORTANT – Observe all governing codes and ordinances.
Note to Installer – Be sure to leave these instructions for the
1
consumer's and local inspector's use.
Note to Consumer – Keep these instructions with your Owner's
2
Manual for future reference.
Skill Level – Installation of this dishwasher requires basic
3
mechanical and electrical skills. Proper installation is the
responsibility of the installer. Product failure due to improper
installation is not covered under the SHARP Consumer Limited
Warranty.
Completion Time – 1 to 3 Hours. New installations require more
4
time than replacement installations.
IMPORTANT – The dishwasher MUST be installed to allow for
future removal from the enclosure if service is required.
If you received a damaged dishwasher, you should immediately
contact your dealer or builder.
INSTALLATION PREPARATION
PARTS SUPPLIED:
NAME & DESCRIPTIONS
Flat Head Wood Screws to
secure dishwasher to underside of
countertop (in literature package)
Screw Type Hose Clamps
Drain Hose
Top Mounting Clips
Dishwasher: SDW6757ES
INSTALLATION MANUAL
QTY.
PARTS
4
1
1
2
FOR YOUR SAFETY - Read and observe all CAUTIONS
and WARNINGS shown throughout these instructions. While
performing installations described in this booklet, gloves, safety
glasses or goggles should be worn.
To reduce the risk of electric shock, fire, or injury to
persons, the installer must ensure that the dishwasher
is completely enclosed at the time of installation.
READ CAREFULLY.
SAVE THESE INSTRUCTIONS.
If you have an installation problem, contact your dealer or installer.
You are responsible for providing adequate electrical, exhausting
and other connecting facilities.
MATERIALS REQUIRED:
NAME & DESCRIPTIONS
Ferrule, Compression Nut and
90° Elbow (
3
/
" NPT external
8
thread on one end, opposite end
sized to fit water supply)
Thread Seal Tape
UL Listed Wire Nuts
1
1
WARNING
QTY.
PARTS
1
1
3

Advertisement

loading

  Also See for Sharp SDW6757ES

  Summary of Contents for Sharp SDW6757ES

  • Page 1 READ CAREFULLY. responsibility of the installer. Product failure due to improper SAVE THESE INSTRUCTIONS. installation is not covered under the SHARP Consumer Limited If you have an installation problem, contact your dealer or installer. Warranty. You are responsible for providing adequate electrical, exhausting Completion Time –...
  • Page 2: Installation Preparation

    INSTALLATION PREPARATION MATERIALS FOR NEW INSTALLATIONS TOOLS REQUIRED: ONLY: NAME & DESCRIPTIONS PARTS NAME & DESCRIPTIONS PARTS Phillips Head Screwdriver " and " Nut Driver Air Gap for Drain Hose, if required 6" Adjustable Wrench Level Waste Tee for House Plumbing, if applicable Carpenter's Square Electrical Cable or Power Cord,...
  • Page 3: Cabinet Dimensions

    • Follow local codes and ordinances. areas shown in Figure A for the drain hose connection. The hole should be smooth with no sharp edges. • Do not exceed 10 feet in distance to drain. • Do not connect drain lines from other devices to the dishwasher...
  • Page 4: Installation Instructions

    " maximum diameter hole to allow the electrical cable. open circuit breaker before beginning installation. The hole must be free of sharp edges. If the cabinet wall is metal, Do not use an extension cord or adapter plug with the hole edge must be covered with a bushing.
  • Page 5 INSTALLATION INSTRUCTIONS WATER LINE CONNECTION STEP 2: ADJUST LEVELING LEGS • Turn off the water supply. • Move the dishwasher close to the installation location and lay it on its back. • Install a hand shut-off valve in an accessible location, such as under the sink.
  • Page 6 Skip this step if dishwasher will be direct wired. Use power cord • Install the screw type hose clamps to the drain hose. kit WX09X70910 available for purchase from an authorized Sharp • Connect the drain hose to the drain hose installation hose, then parts dealer.
  • Page 7: Step 9: Position Dishwasher Under Countertop

    INSTALLATION INSTRUCTIONS STEP 8: SLIDE DISHWASHER PARTIALLY INTO STEP 10: LEVEL DISHWASHER CABINET Dishwasher must be level for proper dish rack WARNING DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. operation and wash performance. DAMAGE WILL OCCUR. • Place level on door and rack track inside the tub as shown to check •...
  • Page 8: Step 11: Secure Dishwasher To Cabinet

    INSTALLATION INSTRUCTIONS METHOD 2 – To install on the side boards: STEP 11: SECURE DISHWASHER TO CABINET METHOD 1 - To install using Top Mount Cabinet Clips: In case counter tops are made of marble, granite, or other hard materials that could not be drilled, use the installation method below. Depending on the depth of the cabinet, the Top Mount Clips have a break-off point that can be removed if necessary.
  • Page 9 INSTALLATION INSTRUCTIONS STEP 13: CONNECT DRAIN LINE When connecting drain line to IMPORTANT disposer, make sure that the drain plug has been FOLLOW ALL LOCAL CODES AND ORDINANCES. Remove removed. DISHWASHER WILL NOT DRAIN The drain hose molded end will fit ", "...
  • Page 10: Step 15: Pre-Test Checklist

    INSTALLATION INSTRUCTIONS • Open dishwasher door and make sure most of the water has STEP 15: PRE-TEST CHECKLIST drained. If not, check that disposer plug has been removed and/ Review this list after installing your dishwasher to avoid charges or air gap is not plugged. See Step 13. Also check drain line for for a service call that is not covered by your warranty.
  • Page 12 SHARP ELECTRONICS CORPORATION • 100 Paragon Drive • Montvale, New Jersey 07645 • USA Sep 23, 2019...