Frigidaire FRA25ESU2 Installation Instructions page 2

Insert 4 screws from inside of cabinet and secure to top angle rail. FIG.8 Top angle rail 2. From inside of cabinet insert 3 screws to attach each side retainer
as shown in Fig. 8. Attach side retainers with flat side against cabinet and angled edge toward rear of cabinet. 3 Assemble Window Filler Panels 1. Place
cabinet on floor, a bench, or a table. 2. Slide "I" section at end of window filler panel into side retainer on each side of the cabinet (see FIG.
9 and FIG.10). Foam Gasket 3. On each side of cabinet, insert top and bottom legs of window filler panel frame into channel in the top and bottom angle
Insert a 7/16" locking screw and flat washer into hole on top leg of each window filler panel (see section 6). Do not totally tighten. Allow leg to slide freely.
Screws will be tightened after Section 6. 3 Installation Instructions T P TOP "I WINDOW TAINER 4 Place Cabinet in Window 1 P FIG.
11 For wooden window: Y For Vinyl-Clad window: FIG.13A FIG.12 HEX-HEAD SCREW B A FIG.13B C 5 Install Support Bracket T T FIG.14 FIG.15B .
SCREWS AT T RT FIG.15A 4 Installation Instructions 6 Extend Window Filler Panels and attach to top angle rail: 1. Carefully raise window to expose filler
2. Extend panels to fill window opening completely. Tighten locking screws on top (FIG. 16). 3. Close window behind top angle rail. 4. HEX-HEAD locking
screw through the hole in the middle of top angle rail into the window frame as shown (FIG. 17). FIG.
16 FIG. 17 LOCKING SCREWS Locking Screw and Washer HEX-HEAD SCREW 7 Attach Window Filler Panels to Window Frame C FIG. 18A A Window
2. Use a 1/8" drill bit to drill a starter hole through the hole in the top leg of each window filler panel and into the window sash (Fig. 18A and Fig. 18B).
8 Install Window Sash Seal and Safety Lock A A. 1. Trim window sash seal to fit window width. Insert it into screw space between upper and lower sashes as
shown (FIG. 19). B. left-hand Window Filler 2. Attach right angle safety lock to top window sash as A. Panel Top Leg shown (FIG.20).
screw C. Window channel 3. If necessary, trim weather seals to needed length, peel off protective backing, and use to plug any gaps. See Fig. 18B. FIG. 21
FIG.20 FIG.19 WINDOW SASH SEAL SAFETY LOCK hex-head screws Vent control correct location 9 Install Air Conditioner into Cabinet and Install Front
2. CAUTION: Do not push on controls OR finned coils. 3. Be sure air conditioner is firmly seated towards rear of cabinet. 4.
Reconnect electronics plug if present. Position vent control lever so that it will thread into its channel in the front panel (see FIG.21). Hook front panel top
tabs into slots on cabinet top, and rotate front panel down so that side tabs snap into place on cabinet. Insert 4 previously removed screws through front panel
5. Insert air conditioner filter. Reinstall the front grille by hooking bottom tabs into slots on Front Panel bottom, then rotating grille up to snap into place. 5
Installation Instructions Thru-The-Wall Installation NOTE: 1 Select Wall Location This air conditioner slides out from its cabinet, so that it can be installed
through an outside wall as explained below. NOTE: IMPORTANT: Side louvers must never be blocked. All parts needed for Thru-The-Wall Installation are
provided, except a wood frame, shims, and 10 wood screws 2 Prepare Wall 22,000~28,500BTU 15,000~18,500BTU FIG.1 FIG.2 Y Inside Inside Width X 6
Installation Instructions 4. Build a wooden frame with the INSIDE dimensions of your model listed above. (Measure twice remember.
) Frame depth should be the same as wall thickness. Fill in the space from the opending to the studs with wood spacers, as shown. 5. Nail frame to spacers to
spacers with front flush with dry wall. NOTE: If wall thickness is 8-1/2" or more, add alumimum flashing over bottom of frame opening to assure no water
panel locking screws on top angle rail. Loosen screws so filler panels slide easily.
Sash B FIG. 18B weather seals 1. Extend the window filler panels out against the window frame.
Panel to Unit 1. Lift air conditioner and carefully slide into cabinet.
can enter area between inner and outer wall. NAIL SPACERS TO STUDS FIG.3 FIG..
Your user manual
FRIGIDAIRE FRA25ESU2
Manual abstract:
rails. 4.
Connect with one 10x1/2" screw.
and into air conditioner.