Table of Contents
Advertisement
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
edges that may be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to
move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over
an extended period of time.
Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp
metal fins of front and rear coils.
Make sure air conditioner does not fall during installation.
If a new electrical outlet is required, have the outlet installed by a qualified electrician before installing unit.
NOTE: DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE.
Preliminary instructions:
Do the following before starting to install unit. See illustrations below.
Check dimensions of your unit to determine model type:
Capacity:
Unit Height:
Unit Width:
Min. Window Opening:
Min. Window Width:
Max. Window Width:
1. Check window opening size: the mounting parts
furnished with this air conditioner are made to install in
a wooden sill double-hung window. The standard parts
are for window dimensions listed above. Open sash to
2. Check condition of window: all wood parts of window
must be in good shape and able to firmly hold the needed
screws. If not, make repairs before installing unit.
3. Check your storm windows: If your storm window
frame does not allow the clearance required, correct by
storm window while room air conditioner is being installed.
FIG.1
sash
inner sill
outer sill
storm window frame or
other obstruction
Installation Instructions
READ BEFORE INSTALLING UNIT
Heavy duty
Medium
window sash seal
safety lock and
long hex
head screw
foam gasket
washer head
locking screw
frame
assembly
(left)
side retainer
screws and
locknuts
bottom rail
seal to unit
long flat
head bolt
FIG.2
sash
outer sill
storm window frame or
other obstruction
top angle
long
window
support bracket
sill angle
bracket
inner sill
board thickness as
required, along entire inner
window sill; fasten to inner
sill with two nails or screws.
frame
assembly
(right)
1
Advertisement
Table of Contents
Related Manuals for Frigidaire 2020219A0951
Summary of Contents for Frigidaire 2020219A0951
-
Page 1: Installation Instructions
To prevent injury or strain, use proper lifting and carrying techniques when moving unit. Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended period of time. -
Page 2: Heavy Duty
5. Check the available electrical service Power supply must be the same as that shown on the unit serial nameplate. (See Use & Care Guide for serial plate location.) Power 6. Carefully unpack air conditioner window support brackets) Tools Required... -
Page 3: Window Mounting
9. Add two foam inserts to holes in top of cabinet where shipping screws were removed from. (See FIG.6) 10. Heavy duty models (22,000~28,500BTU) come with internal shipping packaging. THIS PACKAGING AND PLASTIC TIES MUST BE REMOVED PRIOR TO INSTALLING THE AIR CONDITIONER BACK INTO THE CABINET. (See FIG.7) 11. - Page 4 Installation Instructions Place Cabinet in Window For wooden window: For Vinyl-Clad window: FIG.12 Install Support Bracket FIG.14 TAINER FIG.13A HEX-HEAD SCREW SCREWS FIG.15A “I WINDOW FIG.13B FIG.15B FIG.11...
- Page 5 Insert 4 previously removed screws through front panel and into air conditioner. 5. Insert air conditioner filter. Reinstall the front grille by hooking bottom tabs into slots on Front Panel bottom, then rotating grille up to snap into place.
-
Page 6: Thru-The-Wall Installation
Installation Instructions NOTE: Select Wall Location This air conditioner slides out from its cabinet, so that it can be installed through an outside wall as explained below. NOTE: IMPORTANT: Side louvers must never be blocked. All parts needed for Thru-The-Wall Installation are provided, except a wood frame, shims, and 10 wood screws Prepare Wall FIG.1... - Page 7 LEVEL Prepare and Install Cabinet 1. Slide air conditioner from cabinet; refer back to Step 1 of Window Mounting. 2. Place cabinet into opening with bottom rail resting firmly on bottom board of wooden frame. 3. Position cabinet to achieve proper downward tilt for water removal. Unit must tilt back 5/16" to 3/8" for proper water drainage.
- Page 8 Sill angle bracket Wooden strip 6. Install air conditioner into cabinet by following all steps in Step 9 of Window Mounting. OPTIONAL: Caulking and installation of trim on interior wall may be done. You can buy wood from your local lumber or hardware supply.