Page 2
Thank you for purchasing our ALS-Series UPS. Before operating this system, you should first thoroughly read this manual. After it is read, keep it to the place where the people handled can see it soon. Symbol Marks and Signal Words This instruction manual and the indication with a product have contents for using safely to prevent damage harm property damage.
Page 3
Be sure to follow the below. Do not use for the medical machine and traffic system. Do not use it for the use such as a medical machine concerned with the life, traffic system with the possibility to give it a serious influence from the public society and others.
Page 4
Be sure to follow it because it has the possibility to cause the trouble of the device and a fire when you don't follow the following items. Special knowledge and technology are necessary for the maintenance. Don’t remove a cover. There is a part where a high voltage occurs in the device, and very dangerous.
Page 5
ATTENTION TO SAFETY ・・・・・・・・・・・・・・・・・・・1〜2 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・3 SAFETY USE ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・4 CONTENTS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・5 INTRODUCTION ・・・・・6〜7 The name of each department of the device ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・8 ...
Page 6
ALS series UPS is an advanced true On-Line uninterruptible power system produces reliable and pure sine wave power to users’ equipment, ranging from sensitive medical instruments, computers, telecommunication systems to industrial automatic equipment. The On-Line design enables the system to adjust and filter power fluctuations continuously and automatically under power normal condition.
Page 9
About the place of installation ■ Installation under the following condition causes the trouble of this device. The place of high-temperature and humidity (over 0〜40℃ over 0〜95%RH) Installation in the place of the range of a surrounding Temperature 10-25℃...
Do wiring referring to the following table. Terminal Breaker over 50A Input ExternalBattery Output Start-up and Shut-down 1. Start-up Turn on a battery breaker and an input breaker in the rear. After an alarm rang and bypass operation was done for about thirty seconds, inverter operation (It usually drives.) is done.
Page 11
Special Setting 2. In the special setting, the setting of output voltage and green mode (saving energy mode) can be set at dip switch in the rear. At the setting of output voltage, use the switch1 and 2. At the setting of Green Mode, use the switch 3. The setting of output voltage 2−1...
Page 12
The setting of Green Mode. 2−2 The green mode is the saving energy mode that bypass operation is done at the time of the low load. Green Mode starts automatically under 360W. It is not necessary to restart. ...
Page 13
Functions 3. −Self-Diagnosis of Battery− Push a TEST Key about two seconds at the inverter operating. Self-diagnosis of Battery is done. If there is no wrong point, after ten seconds it is returned to the inverter operating. If there are a few amounts of battery, an alarm rings, and it is returned to the inverter operating soon.
Page 14
Problem Causes Solutions UPS no reaction while AC No AC input Check AC power is connected UPS fault Call for service Battery damaged Call service to replace batteries Input / output sensor fault UPS no reaction while AC Call for service...
Page 15
Problem Causes Solutions Line LED flickers AC grounding wire abnormal Check grounding wire with assistance of power engineering service After AC connected to UPS, AC abnormal Check AC power alarm sounds short and fast beeps and UPS shut down ...
SPECIFICATION Model Specification ALS-5KH UPS Type On-Line Type Capacity 5000VA / 3500W Phase Single Phase 2 Wire Voltage (V) 200/220/230/240 Voltage Accuracy Within 3% 85%TYP Efficiency Transient Response Within 7%(0 ⇔ 100% Load Step) Wave Form Pure Sine Wave Overload Capacity 120%...
Page 17
http://www.yamabishi.co.jp TOKYO OFFICE Email : sales@yamabishico.jp 2-4-18 Omorikita Ota-ku Tokyo Japan TEL 813-3767-8861 FAX 813-3767-7080 ...