Advertisement
Safety Warnings
• This product is only suitable for connection to 240V~50Hz supply. It is recommended that this light is
installed by a qualified electrician in accordance with current IEE Wiring Regulations and local Building
Regulations
• Before installing your light fitting always switch off the mains supply and remove the appropriate fuse or
switch off the appropriate circuit breaker before commencing installation.
• This is a Class I fitting, and must be connected to Earth.
requirements of the fitting.
• Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F
1.0mm2 (not supplied) to selected site, ensuring it is adequately protected through the full length of the
cable run, it must come out of the flat surface of the mounting surface in line with the entry to the fitting.
• Except where installed in a conduit or duct , which provides equivalent protection against mechanical
damage, a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable
for use as a protective conductor, or be of insulated concentric construction. Buried cables shall be marked
by cable covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried
cables, conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably
foreseeable disturbance of the ground.
• Never fit bulbs of a higher wattage than those specified on the label (as these may cause overheating and
damage the fitting).
• This product contains delicate parts. Take care during installation and maintenance to avoid breakages
• If you are in any doubt about your competence please consult a qualified electrician.
• If any modification is made it will invalidate the warranty and may render the product unsafe.
• This product must only be installed to a solid, fixed surface, such as concrete, decking or paving slabs. It
must NOT be installed on soil.
Care Information
Allow 10 minutes to cool before replacing, adjusting or cleaning.
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
Assembly/ User Instructions
Please read these instructions carefully before fitting and retain for reference.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly.
Ensure that the product is fully assembled as illustrated before use.
The Light pack contains:
Light fitting.
Terminal connection block(s).
Fixing pack.
6 x Glass panels
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.
Endon Lighting, LS9 0SE
Burford Outdoor Post Light
INSTRUCTION MANUAL
Before you start
The terminal blocks are supplied according to
The following tools may be required:
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
76549-Burford-Post 20181127
Advertisement
Table of Contents
Related Manuals for Endon Burford Outdoor Post Light
Summary of Contents for Endon Burford Outdoor Post Light
- Page 1 Burford Outdoor Post Light INSTRUCTION MANUAL Safety Warnings • This product is only suitable for connection to 240V~50Hz supply. It is recommended that this light is installed by a qualified electrician in accordance with current IEE Wiring Regulations and local Building Regulations • Before installing your light fitting always switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker before commencing installation. • This is a Class I fitting, and must be connected to Earth. The terminal blocks are supplied according to requirements of the fitting. • Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2 (not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it must come out of the flat surface of the mounting surface in line with the entry to the fitting. • Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage, a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables, conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable disturbance of the ground. • Never fit bulbs of a higher wattage than those specified on the label (as these may cause overheating and damage the fitting). • This product contains delicate parts. Take care during installation and maintenance to avoid breakages • If you are in any doubt about your competence please consult a qualified electrician.
- Page 2 Assembly/ User Instructions Continued 1. Determine the position of your light fitting taking into account the entry position of the cable and make sure there is sufficient cable coming out of the floor to connect to the terminal block. Ensure that the mounting surface is solid, preferably a brick or block floor and ensure that there are no other cables or pipes beneath the surface. 2. Diagram A: Connect the house wiring to the terminal block (Fig 2.). Remove the terminal bracket from the base. Remove the terminal block box lid. Connect the mains supply. Replace terminal block box lid. Replace terminal bracket onto base. NOTE: This is a Class I fitting and must be earthed. Check the seal, use sealant if required. 3. Diagram B. Use appropriate fixings to secure the post to the mounting surface (1&2) 4. Fit the glass pieces into their slots in the frame (3). 5. Fit the bulb (not supplied) into the lamp holder (4). NOTE: Never fit a bulb of a higher wattage than that specified on the label (as this may cause overheating and damage the fitting). 6. Attach the lid of the fitting with the hex nuts (5), ensuring a good seal to maintain ingress protection. 7. Turn on the power and test. Diagram A Diagram B Endon Lighting, LS9 0SE 76549-Burford-Post 20181127...
Need help?
Do you have a question about the Burford Outdoor Post Light and is the answer not in the manual?
Questions and answers