Advertisement
ENG
ENGLISH
ENGLISH
HOT LAMINATION STEPS
1
2
1. Connect power cable to power
2. Switch laminator on with
and to inlet at back of laminator.
Power On / Off button at back
of machine
4
5
80
100
125
175
4. Use navigation keys to select setting
5. Press the round select key when the desired
for the hot lamination pouch thickness
thickness is indicated on the LEDs and wait for
(3-7mil) you wish to laminate.
the acoustic signal and the Ready Light next
to the selected pouch thickness.
7
8
80
100
125
175
7. Green Wait LED will fl ash and acoustic
8. While laminator is warming up, please
bleep signal will sound when machine
prepare item you wish to laminate. Place the
is ready to laminate selected pouch
item inside the pouch and centre it against
thickness.
the sealed edge of the pouch. To prevent
jamming, use a carrier when item is smaller
than the pouch.
10 0
11
10. To prevent jamming, immediately
11. Before switching off laminator, feed
remove laminated item from back of
empty cleaning/carrier sheet through
machine. Let item cool on fl at surface for
machine to clean unit.
several seconds.
4
Jupiter125_402104_3L_1112806.indSec4:4-Sec5:5 Sec4:4-Sec5:5
Jupiter125_402104_3L_1112806.indSec4:4-Sec5:5 Sec4:4-Sec5:5
3
80
100
125
175
3. Press Stand-by button at left of front
operating panel to switch laminator on.
6
80
100
125
80
100
125
175
175
6. Confi rm your selection by pressing
"Enter" button in the middle of navigation
keys. Laminator will take a few minutes
for temperature adjustment.
9
9. Place pouch, sealed edge fi rst, into
laminator entry. Keep pouch straight
and use the edge guide to centre it.
MAINTENANCE - Unique Easi-Acc
MAINTENANCE - Unique Easi-Access technology
MAINTENANCE - Unique Easi-Access technology
NCE U i
U i
E
E i A
E i A
A
h
h l
h l
h l
This laminator is equipped with the unique Easi-Access technology for easy maintenance. This allows the user to open the laminator for maintenance, just like a photocopier.
i t i
i d ith th
i
E i A
t h l
f
i t
Thi ll
1
2
80
100
125
175
1. To open the laminator, please press
2. Fans will turn on to cool the machine
the "Open" button as shown in the
down to safe handling temperature
illustration and wait for the "open"
inside.
LED to switch on and the ready beep.
5
6
5. Open the lid with both hands.
6. For further maintenance, the rollers
can be released by experienced users.
You are now able to clean the inside of
Press cam levers to release the rollers.
the laminator and carefully remove any
residual glue or other items.
When laminator is opened, power to
internal parts is isolated, so that user is
not in danger of electric shock.
TROUBLESHOOTING
1
2
80
100
175
Problem
Cause
Ready Light does not go on after extended time
Laminator is in a hot, humid area.
Pouch did not completely adhere to item
Laminated item may be too thick.
Jamming
Pouch was not used.
Pouch was not centred or straight when fed
through Pouch/Document Entry.
Need Help?
Please call our experts at
Customer Service. You'll fi nd
the numbers for your nearest
Service Centre on the
BACK cover of this booklet.
WARRANTY
Fellowes warrants all parts of the laminator to be free of defects in material and workmanship for 2 years
from the date of purchase by the original consumer. If any part is found to be defective during the warranty
period, your sole and exclusive remedy will be repair or replacement, at Fellowes' option and expense, of
the defective part. This warranty does not apply in cases of abuse, mishandling or unauthorized repair. ANY
IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED IN DURATION
3
4
80
100
125
175
3. The "open" LED will turn on and the
4. Press the red buttons on both sides of
ready beep will sound when machine is
the machine to activate the Easi-Access (The
ready to be opened.
laminator needs to be switched on to allow
the active temperature control to work).
7
7. Please remember to re-secure them to
ensure safe operation.
3
125
Solution
Move laminator to a cool dry area.
Pass through laminator a second time.
All our laminators have been designed to operate jam-free.
g
g
p
p
In the unlikely event of a jam occurring, please press the red
y
y
g p
g p
p
p
g
release buttons on the sides of laminator, and wait for the
open light to turn on. (See image 1)
The laminator can be opened to remove incorrectly inserted
items as described under maintenance. Please ensure that
you follow the described steps. (See image 2)
Gently pull on the jammed material to release it. (See image 3)
Make sure that no residue is left on the rollers and use
cleaning sheet before laminating.
Always put item in a pouch.
Align sealed edge with Pouch/Document Entry. Use guide
to centre.
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. IN NO EVENT SHALL FELLOWES BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ATTRIBUTABLE TO THIS PRODUCT. This warranty
gives you specifi c legal rights. You may have other legal rights that vary from this warranty. The duration,
terms and conditions of this warranty are valid world-wide, except where different limitations, restrictions or
conditions may be required by local law. For more details or to obtain services under this warranty, please
contact us or your dealer.
11/28/06 10:30:33 AM
11/28/06 10:30:33 AM
5
Advertisement
