Download Print this page

Advertisement

Quick Links

Introduction
LANsmart Pro is a hand-held, multifunction Cable Map Tester and Cable Length
Meter.
It has an integrated Analog and Digital Tone
Test. It displays cable map results in a pin-to-pin format including split pairs. By
using TDR (Time Domain Reflect) technology, it provides
when measuring cable length and locating split pairs. It is suitable for professional
technicians or installers.
Features:
• All-in-one tester: wire map, twisted mapping, short location, quick test, cable
length test, self-calibrating ability, analog and digital tone generator and port
finder.
• Incorporates TDR (Time Domain Reflect) Technology
• Wire map for open, short, reversed, cross, split, miswire, and shield continuity
• Wire map results are displayed in a pin-to-pin format
• Indicates the remote number of the remote identification unit for wire map test
• Incorporate Short Location function: locate short position,
short is in the near or far end of the
• Measures twisted pairs of Cat5, Cat5E and Cat6 length without remote
• Measures
length of
• Measures coax line length
Self-calibrating
measuring accuracy
• Uses both meter and feet standards for cable length display
• Incorporate Quick Test function: memorize a cable's pin out as standard, and
test mass cables.
• Incorporates Port Finder function: locate corresponding socket on hub/switch
• Its
Analog
Tone Generator sends 1K Hz tone
conductors.
Its Digital Tone Generator sends Single Tone and Double
• LCD and "beep" indicator
• RJ45/ RJ11/COAX port protection from telephone line damage
• Replaceable battery, with low battery indicator
Contents:
1 LANsmart Pro Main Unit
4 Remote Unit: ID1, ID2, ID3, ID4
LANsmart Pro user manual
flat 2-pin, 4-pin and 6-pin telephone line
ability for non-standard cables length test
Generator, Port Finder, and Quick
a great deal
cable.
on all pins or selected single pin
1
of accuracy
it determines if
to enhance
Tone.

Advertisement

loading
Need help?

Need help?

Do you have a question about the LANsmart Pro and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hobbes LANsmart Pro

  • Page 1 LANsmart Pro user manual Introduction LANsmart Pro is a hand-held, multifunction Cable Map Tester and Cable Length Meter. It has an integrated Analog and Digital Tone Generator, Port Finder, and Quick Test. It displays cable map results in a pin-to-pin format including split pairs. By...
  • Page 2 Specifications • Display: 128*64 Dot Matrix LCD • Connector Type: RJ45/RJ11/COAX (Main and Remote) • Accuracy: ± 2m less than 10m (± 6.56 Feet in less than 32.81 feet) ± 5% over 10m (32.81 feet) • Test range for cable length: 0-300m (0 – 984 feet) •...
  • Page 3 When choosing wire map test object (twisted cable, telephone line or coax line) and calibrating parameters for non-standard cable length test, user must do the following configuration. Follow the steps to configure the LANsmart Pro: 1. Turn on the LANsmart Pro 2. LANsmart Pro will self-diagnose first.
  • Page 4 For example, network cable calibration page explanation: Ntwk 10 M • Ntwk—the calibration object is network twisted pair. • Cal xx M-------It is the cable length supplied by LANsmart Pro when using default parameter • “+ and –” to change the Cal—value...
  • Page 5 Before wire map test, user should setup test object (twisted cable, telephone line, or coax line) Configuration menu. Connect one end of tested cable to LANsmart Pro main unit, and the other to the remote. Select the Cable Test option from the Main Menu, and then select Wiremap,...
  • Page 6 Pins are miswire. 8 1 2 7 5 6 4 3 Fail LANsmart Pro can also identify and indicate the remote identification number attached to the far end of the subject cable. 1 2 3 4 5 6 7 8 G...
  • Page 7 Select “Yes” to continue. Select go to previous menu. If the cable is shorter than 1.2 meter, the LANsmart Pro can not identify the twisted status, it will show the warning message “Cannot detect cable under 1.2m”.
  • Page 8 Quick Test This function is used to test a number of cables. First, LANsmart Pro records a cable pin out status. We call it standard cable. Next, it tests another cable to judge whether the tested cable’s pin out status is the...
  • Page 9 Fail! standard cable, the beeper beeps “Bi—Bi—Bi--”, and LCD displays “Fail” Length Test LANsmart Pro can measure the length of twisted cable, flat telephone line and coax line. Before test, user should setup the type of cable to be tested in the Configuration menu.
  • Page 10 Green clips to the Green wire and White clips to the Green white wire. 4. Test the cable length. Tone Generator At 1 KHz frequency, the LANsmart Pro emits an audio signal to a cable; user can trace the cable with corresponding cable tracer. Select the Analog Tone options from Identification menu...
  • Page 11 (Port Finder menu) Warning: Telephone line connection When LANsmart Pro’s RJ45/RJ11 port is connected an active telephone line, sends out a warning message “High Voltage Detected! Please Reset” and causes all function module to stop working. You must immediately turn off the unit!