Related Manuals for Kroll Kozy MTM52
Summary of Contents for Kroll Kozy MTM52
- Page 1 Kroll’s Kozy Waste Oil Heater MTM52 * *Distributed and supported by Kroll Heaters, Australia, Sales & Service ring 1800 805 243...
-
Page 2: Environmental Conditions
1. Heater intended application and technical data The universal oil heater type MTM 52 is designed to heat industrial rooms not covered with central heating systems (workshops, car repair shops, industrial shops, warehouses, storage buildings, basements, garages, etc.). The heater can operate using most waste oils of mineral and plant origin, e.g. engine, gear, hydraulic, fuel oil, with maximal density in temperature of 15°C equal to 860 kg/m3 and with ignition temperature exceeding 56°C. -
Page 3: Safety Aspects
4. Safety Aspects It is inadmissible to use fuels other than specified in heading 1. of this manual. In particular, it is forbidden to use such fuels as solvents or petrol All activities regarding operation of thedevice must be performed in protective gloves and by a person trained for operation. -
Page 4: Installation
6. Installation • read the local Healty and Safety and fire protection regulations, • place the heater on a flat, concrete floor, in the spot allowing free space around the device, according to Fig. 2., • level the device - in order to check whether the heater is well levelled, place the furnace bowl in the lower part of the combustion chamber and pour a small amount of diesel oil into it - the oil should spill out exactly in the middle of the bowl, •... -
Page 5: Flue Installation
7. Flue installation The flue spigot of the MTM 52 heater must be capped with the draught regulator (which is a part of the standard heater equipment) in the vertical position so that the exhaust fumes outlet is directed upwards. The stack must be installed into the exhaust fumes outlet of the draught regulator. -
Page 6: Device Operation Description
8. Device operation description Control panel: The controller of universal oil heater type MTM 52 is equipped with an adjusting knob and two switches, stop and start, which enable the user to control the heater operation, and five light emitting diodes [leds] indicating the operation phase of the device, connected to an alarm in case of a failure. - Page 7 Fig. 6. The distribution of the heater safety components: Control thermostat and STB thermostat Overflow cut-out (micro-switch)
-
Page 8: Operation
9. Operation CAUTION oil must not be poured into the fuel tank during device operation. oil must not be poured into the furnace and it must not be fired up if the furnace chamber or bowl are still hot!!! always wait until the burner plate has cooled down entirely. -
Page 9: Maintenance
Maintenance The heater requires little maintenance activity. Following the manufacturer’s recommendations will ensure safe and failure-free operation of the device: • clean the furnace bowl and other combustion chamber elements everyday before firing up. The maximal device operation time without cleaning the bowl is about 7-12 hours (depending on the employed oil intended for combustion) •... - Page 10 11. Faults,Causes & Solutions In the case of the device failure, the following list may help to determine its location. Generally, its removal is fairly easy. The most frequently occurring problems are listed below. . NOTE: Prior to performing any maintenance or repair activity of the device, disconnect its power plug from the power socket.
- Page 11 EC DECLARATION OF CONFORMITY MTM DARIUSZ SEFERYŃSKI HEATING, VENTILATION, AIR CONDITIONING 04- 239 WARSAW, ul. MŁODNICKA 52 C I hereby declare that the oil air heater intended for heating industrial rooms without central heating systems: Rated power of 30-52 kW Due to its design and structure, meets the basic safety and health requirements set forth in the Directive 2006/42/EC on machinery and has been manufactured according to the directives as follows: ...
- Page 12 This declaration pertains only to the machine in condition in which it was launched on the market and does not cover component parts added by the end user or later actions performed by them. This declaration expires if any changes are made to the device that have not been consulted with us. Warsaw, on ....
Need help?
Do you have a question about the Kozy MTM52 and is the answer not in the manual?
Questions and answers