Table of Contents
Advertisement
Owner's / Installation Manual
Important!
This manual covers the installation and operation of the PoolSync
Read this manual and product labels before installing or operating this equipment.
INSTALLER: This document is the Purchaser's property and is to remain with the
equipment owner.
device.
TM
LTP0160 REV 2.0
Advertisement
Table of Contents
Related Manuals for Aquacal AutoPilot PoolSync
Summary of Contents for Aquacal AutoPilot PoolSync
- Page 1 Owner's / Installation Manual Important! This manual covers the installation and operation of the PoolSync device. Read this manual and product labels before installing or operating this equipment. INSTALLER: This document is the Purchaser's property and is to remain with the equipment owner.
-
Page 3: Table Of Contents
Table of Contents Safety Information Safety Information General Information Contacting AquaCal AutoPilot, Inc. How Your PoolSync Works Control Panel Overview User Display Reset Button LED Service Mode Button LED Service Access and Setup Button LEDs Installation Wiring to a PoolSync Ready Device ®... -
Page 4: Safety Information Safety Information
SAFETY INFORMATION Safety Information IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS Follow all state provincial and NEC (National Electrical Codes) and applicable CEC (Canadian Electrical Codes) unless local guidelines supersede. -
Page 5: General Information Contacting Aquacal Autopilot, Inc
GENERAL INFORMATION Contacting AquaCal AutoPilot, Inc. If you need to contact AquaCal AutoPilot, Inc. for questions, service, or parts, please have your model and serial number of the equipment being controlled by the PoolSync available. Also have the name of your installer and date of your equipment’s installation. -
Page 6: Control Panel Overview User Display
CONTROL PANEL OVERVIEW User Display PoolSync Label Figure 1 Reset Button LED Pressing this button will allow the PoolSync to be reset. Blinking: Indicates the PoolSync unit is Offline and not connected to the network. Fading: Indicates the PoolSync is connected to the local home router. -
Page 7: Installation
INSTALLATION WARNING - Failure to heed the following may result in permanent injury or death. RISK OF ELECTRICAL SHOCK - Disconnect all AC power when installing or servicing this system. Follow all state, local, and National Electrical Code(s) (provincial and Canadian Electrical Code(s) if applicable). - Page 8 Black wire from PoolSync to BLK (or GND) Yellow or White wire from PoolSync to YEL (or A) Green wire from PoolSync to GRN (or B) Red wire from PoolSync to RED (VDC or 10v) PoolSync Wiring Figure 2 ChlorSync ®...
-
Page 9: Aquacal Heat Pump Wiring
The installer must be familiar with service industry techniques. ® AquaCal Heat Pump Wiring 1. Turn off all power to the heat pump. Wait for 2 minutes after the shut down of equipment before removing panels. - Page 10 Black wire from PoolSync to G (or GND) Yellow or White wire from PoolSync to Y (or A) Green wire from PoolSync to B Red wire from PoolSync to R (or 10v) Port D Figure 5 Port D Wire Location Figure 6 Note: Before mounting the PoolSync , verify WiFi...
-
Page 11: Chlorsync ® And Aquacal ® Heat Pump Combination
® ChlorSync and AquaCal Heat Pump Combination ® You can control and monitor both the ChlorSync chlorinator and ® ® the AquaCal pool heat pump using one PoolSync device. Choose which unit you wish to connect the PoolSync to and follow the wiring instructions below. - Page 12 The PoolSync must be installed and operated as specified. Failure to do so will void the equipment warranty. ® Connect the PoolSync to an AquaCal heater: 1. Follow the directions shown previously to connect the ® PoolSync to the AquaCal heater.
- Page 13 PoolSync Connected to the ChlorSync ® Figure 7 ® PoolSync Connected to the AquaCal Heater Figure 8 Page - 10...
-
Page 14: Downloading The Poolsync
Downloading the PoolSync You can search the iOS App Store or Google Play Store to download the PoolSync app. Follow instructions to create a new account. Connect the PoolSync to the WiFi 1. Ensure Bluetooth and WiFi are enabled on the mobile device. -
Page 15: Troubleshooting
2. Secure vertically on a flat surface, using the two mounting tabs affixed on either side of the unit. 3. Verify once more that the PoolSync unit is communicating with the pool equipment via the mobile device app. TROUBLESHOOTING Troubleshooting Cannot See PoolSync Device In Mobile App Verify the PoolSync... -
Page 16: Reference Fcc Compliance
REFERENCE FCC Compliance This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Page - 13...