Table of Contents
Advertisement
Quick Links
RC-50M
Rim Clamp
For servicing motorcycle and ATV tire/wheel assemblies
See
Operating
Instructions
on page 2.
1601 J. P . Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359
HENNESSY INDUSTRIES INC. Manufacturer of AMMCO
®
Tire Changer
Installation Instructions
Operating Instructions
Safety Instructions
Maintenance Instructions
READ these instructions before placing unit in
service KEEP these and other materials delivered
with the unit in a binder near the machine for
ease of reference by supervisors and operators.
®
, COATS
®
and BADA
®
Automotive Service Equipment and Tools.
®
with Parts List
Manual Part No.:
Revision:
85000625 00
06/07
Advertisement
Table of Contents
Related Manuals for HENNESSY INDUSTRIES Coats Rim Clamp RC-50M
Summary of Contents for HENNESSY INDUSTRIES Coats Rim Clamp RC-50M
- Page 1 1601 J. P . Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 Manual Part No.: 85000625 00 HENNESSY INDUSTRIES INC. Manufacturer of AMMCO ® , COATS ® and BADA ®...
-
Page 2: Table Of Contents
Table of Contents Safety Instructions Safety Instructions .....iii Owner’s Responsibility To maintain machine and user safety, the responsibil- Owner’s Responsibility ..... .iii ity of the owner is to read and follow these instructions: Operator Protective Equipment . -
Page 3: Operator Protective Equipment
Safety glasses with side copies of either, or further information, con- shields, goggles, or face shields are acceptable. Back tact: belts provide support during lifting activities and are Hennessy Industries, Inc. also helpful providing operator protection. -
Page 4: Know Your Unit
Principal Operating Parts Know Your Unit Compare this illustration with the unit before placing it into service. Maximum performance and safety will be obtained only when all persons using the unit are fully trained in its parts and operation. Each user should learn the function and location, of all controls. - Page 5 Bead Loosener (Optional) Bead Loosener shown separately for clarity Part Number 85000503 Important: Always read and follow the operating instructions. • 1...
-
Page 6: Operating Instructions
Operating Instructions CAUTION This unit must be properly operated and properly maintained to help avoid accidents that could damage Loosening the beads on a partially or fully the unit and injure the operator or bystanders. This sec- inflated tire is unsafe and causes excess tion of the Operating Instructions manual reviews movement and friction against the bumper basic operations and use of controls. - Page 7 3. Turn the wheel around and repeat loosening pro- clamps inward until they contact the rim. Observe cedure on the other side of the wheel. This should be closely to prevent tire/wheel damage. If clamps are the long side of the drop center. properly positioned and the tire/wheel assembly is secure, loosen the tabletop locking knob and proceed.
- Page 8 12. Rotate the bead lifting tool down towards the wheel to lift the tire bead up and over the knob portion of the demount head. The lift tool may be removed if desired (figure 11). Figure 8 - Adjust Swing Arm to Position Head Roller 10.
- Page 9 Motorcycle Figure 13 - Demounting Lower Bead 15. Turn the table top to rotate the wheel. The demount head will guide the bead up and over the edge of the wheel. Continue rotation until lower bead is demounted. Note: With tube-type tires, demount the upper bead and remove the tube before demounting the lower bead.
-
Page 10: Mounting
Mounting 3. Lubricate tire beads liberally with tire manufac- turer approved lubricant (figure 15). This information must be read and followed carefully to prevent accidents and injuries during mounting. WARNING Check tire and wheel carefully before mounting. Make sure the tire bead diameter and wheel diameter match exactly. -
Page 11: Inflation
Note: For tube type tires, mount the lower bead first, move swing arm out, install the tube, and then mount the upper bead. When you have completed the mounting process, proceed to inflation. Inflation DANGER Do not inflate tire while wheel is clamped to the Table Top. -
Page 12: Maintenance Instructions
Maintenance CAUTION Instructions Read and follow all the maintenance instructions pro- Replace any damaged or missing safety vided in this manual to keep the machine in good oper- decals. They are available from COATS, (800) ating condition. Refer to the other materials received 688-6359. -
Page 13: Installation Instructions
Installation Instructions holding pin completely through the guild hole prior to locking the wheel in place. CAUTION Bead-head Adjustment: Prior to using your RC-50M you should take a few moments to check the align- ment of the bead-head. This is a simple procedure that Proper unit installation is necessary for safe will require a 4.5mm hex wrench and an 18-inch wheel. -
Page 14: Parts List
Parts List PART NO. DESCRIPTION PART NO. DESCRIPTION 85000717 MOUNT HEAD 85000722 NYLON NUT 85000718 O-RING 85000723 85000719 RIM PROTECTOR 85000724 ADJUSTER HEAD 85000720 RUBBER GRIP 85000725 HANDLE 85000721 FLASH BOLT 8184712 PLASTIC BOOTIE 10 • Important: Always read and follow the operating instructions. - Page 15 Notes Important: Always read and follow the operating instructions. • 11...
- Page 16 ADDITIONAL COPIES, CONTACT THE COATS ® SERIOUS INJURY OR DEATH TO OPERATOR COMPANY, 1601 J.P . HENNESSY DRIVE, AND/OR BYSTANDERS. LAVERGNE, TENNESSEE, 37086 - (800) 688-6359. 85000625 00 06/07 © Copyright 2007 Hennessy Industries and COATS All Rights Reserved Printed in USA...