Table of Contents
Advertisement
8. Insert the new GRO-75EN RO Membrane Cartridge into
position in the clip. Rotate the cartridge so the quick-
connect ports line up with the tubing.
9. Push the red and blue tubing into the quick-connect
ports at the bottom. Push the top tubing into the
connector at the top of the cartridge.
NOTE: The bottom of the GRO-75EN RO Membrane Cartridge
will be supported by the lower bracket.
10. Position the 4CC Filter Cartridge under the left side front
head. Line up the tabs on the cartridge with the slots in
the head.
11. Push the new cartridge into the head until it can go no
further.
12. Twist the cartridge a 1/4-turn to the right (clockwise)
until it locks in place. Pull gently down to ensure the
cartridge is locked in place.
13. Position the 4CB5 Cartridge under the left side rear
head. Line up the tabs on the cartridge with the slots in
the head.
14. Push the new cartridge into the head until it can go no
further.
15. Twist the cartridge a 1/4-turn to the right (clockwise)
until it locks in place. Pull gently down to ensure the
cartridge is locked in place.
16. Repeat Steps 6, 7 and 8 for the 4FC5-S Cartridge in the
right side head.
CAUTION: The 4FC5-S Cartridge may contain carbon fines
that will be removed during the initial flushing.
Follow the proper flushing procedure to prevent
damage to the GRO-75EN RO Membrane Cartridge.
INITIAL FLUSHING OF CARTRIDGES
The installation of new cartridges requires that a preliminary
flushing of the cartridges be performed. This initial flushing
is required to prevent damage to the RO cartridge.
Refer to the Installation section, "Putting the System into
Operation" for the complete flushing procedure.
EVERPURE CONSERV 75E SANITIZING PROCEDURE -
CONTAMINATED WATER SUPPLY/BOIL ALERTS
When the water system has been contaminated or a boil
water advisory has been discontinued, the Everpure Conserv
75E System must be sanitized. If a boil water advisory has
just been discontinued: Flush the water lines according to
your water supplier's instructions. OPEN the delivery faucet
and flush the system for about 10 minutes, then follow the
filter cartridge replacement instructions below.
1. Turn OFF the water supply and OPEN the application
valve to relieve pressure.
2. Remove the filter cartridges and discard in trash. Wash
hands with soap and warm water.
NOTE: If a drip pan is used, clean with dish soap and
warm water.
EVERPURE
CONSERV
®
75E HIGH EFFICIENCY RO SYSTEM INSTALLATION AND OPERATION GUIDE
®
NOTE: The following steps require placing bleach into
the Conserv 75E System. Pentair
cartridge, Everpure
Cartridge (EV9608-10), that is designed for this
application. The following steps describe how to use
the Pentair Everpure 2JT Cartridge (EV9608-10).
CAUTION: DO NOT install the Pentair GRO-75EN RO
Membrane Cartridge for the sanitization
procedure. The solution will severely damage the
membrane.
Sanitization Procedure with the Pentair Everpure 2JT
Cartridge (EV9608-10)
3. Grasp the tip of the outlet tower center, top of the
cartridge and pull out gently. The entire central plug with
the long tube attached will come out, leaving a hole.
Figure 11
4. Add about a teaspoon of laundry bleach (5.25% sodium
hypochlorite solution) to the empty flushing cartridge
through the hole in the top.
5. Lubricate o-ring with a high quality silicone lubricant.
Replace the central plug assembly and insert the flushing
cartridge into the right side head location for the Everpure
4FC5-S Cartridge. Refer to Figure 12.
NOTE: Do not use petroleum jelly to lubricate the o-rings. It
will degrade the o-rings.
Open
Power
Switch
Port Plugs
Open
Figure 12
6. Install a plug into the ports for the 4CC and 4CB5 Filter
Cartridges.
NOTE: Plugs were not included with the Conserv 75E
System.
offers a hollow
®
2JT Flushing/Sanitizing
®
Open
Connect
to White
Tubing.
Cartridge
with Sanitizer
Water Supply
Valve Closed
Connect to Blue
Tubing.
15
Hide quick links:
Advertisement
Table of Contents
