Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Huvema HU 1300 X 4 ES
Summary of Contents for Huvema HU 1300 X 4 ES
- Page 1 E L E C T R I C S H E A R I N G M A C H I N E HU 1300 X 4 ES...
-
Page 2: Table Of Contents
OPERATION MANUAL Table of contents Ⅰ St r u c t u r e a n d Fu n c t i o n … … … … … … … … … … … … … … … … 2 Ⅱ... -
Page 3: Ⅰ Structure And Function
Ⅰ STRUCTURE AND FUNCTION This kind of machine is under-drive structure, The small chain wheel which equiped on speed-control motor will take big chain wheel directly, drive the eccentricity wheel of spindle moving seasonally. The mainly part, like machine shelves, upper blade, worktable and so on is steel welding structure. -
Page 4: Ⅲ Tr A N S P O R T A N D I N S T A L L A T I O N
Ⅲ Transportation and installation Transportation : Keep balance when transport the machine! When you transport the machine with fork truck, please refer to picture 1. Installation: Put each mat down to the four ground holes, the depth into the earth must be over 500mm, please refer to picture 2. The Installation methods is that Please set apart the place for the groud holes when the first concrete pouring, put then the machine on the ground after concreting,... -
Page 5: Ⅳ Preparation And Test Drive
The second The first concrete concrete pouring pouring Picture 2 Ⅳ Preparation and test drive 1、 The machine must be cleared after assembling. 2、 Avoid any loosing at the joint part of nut and screw. Make sure there is no barriers at the parts for transferring. -
Page 6: Ⅴ Adjustment For The Shearing Edge Gap
Ⅴ Adjustment for the shearing edge gap 1. Relation between Plate thickness with cutting edge data (Picture 3) (Cutting edge data can cut 2mm when the machine was made out) Thickness （mm） 0.05 0.10 0.15 0.20 Cutting edge（mm） Picture 3 2. -
Page 7: Ⅵ L U B R I C A T I O N
Picture 4 Ⅵ Lubrication (Picture 5) ITEM Lubricate place Quantity Lubricate period Lubricating oil Copper Bushing Once every shift Machine oil Shaft of upper blade Once every shift Machine oil frame Back guard screw bar Once every shift Machine oil... - Page 8 Motor direction Picture 5 This machine should be manual lubricated point by point regularly, the safety guard on the two sides should be removed when you lubricate the point 1 and 2 in the picture 5. Viz. the part Nr.52 and Nr.57 in the exploded drawing.
-
Page 9: Ⅶ Maintenance
VII Maintenance 1、 The machine should be used by an experienced operator. The operator must read this manual carefully before operating. 2、 Keep work area clean. Paint rust-proof oil on un-painted section and sliding section of the machine. 3、 Keep shearing blade edge sharp. If you find any damage or wear or bull, please re-grind the blade or change a new blade. - Page 13 Parts list: Item Description Specification Remark M8X45 washer Back protective screening plastic Plugging covered Upper protective screening retaining rings for shafts M8X70 column nut washer profile-safety guard Ⅰ cover bolt M8X55 corbel piece square nut adjustable shelves M8X40 bolt M6X12 column nut rubber mat retaining rings for shafts...
- Page 14 profile-safety guard Ⅱ washer M6X12 half-column nut upper shield M5X10 half-column nut washer light upper-blade shelves Brake pad M5X8 Cross recessed countersunk head screw Back Slide bar M5X12 socket set screws with taper point Front slide bar safety guard safety guard Sheet holder for springs blade easily damaged parts...
-
Page 15: E L E C T R I C S Y S T E
M16X65 column nut M12X65 column nut elastic washer washer M16X1.5 M16X1.5X100 column nut M10X25 Table leaf socket set screws with flat point M10X30 68-1 bolt M10X50 socket set screws with flat point M8X10 UCP212 bearing with M16X55 bolt washer machine shelves vibration-control block Electric box Foot switch... - Page 16 travel switch Supporting seating Spindle 14X60 Motor M16X65 bolt chain wheel socket set screws with flat point M8X8 chain 16A(48pieces) eccentric wheel bearing easily damaged parts front-safety guard washer M6X12 half-column nut thin nut flange nut M12X55 column nut elastic washer washer holder block disc spring...
- Page 17 Hex.nut M6X8 Small chain M6X16 Hex. Column nut Spring washer Flat washer M8X25 Hex. Column nut Spring washer Flat washer Plate for motor Hex. Column nut M8X16 Chain Hex. Column nut M6X16 Bearing cover 7204C Bearing 12mm Washer 12mm Spring washer M12X50 Hex.
- Page 18 Seat for screw nut M8X1 Oil cup Block washer encoder 156.1 Seat for encoder Chain M6X35 Hex. Column nut Bushing Hex Bolt M10X70 Adjusting fixed-block Hex. Column nut M10X30 Stand 2 M10X16 Hex. taper nut Screw Shaft 1 Bushing M24X2 Thin nut M8X45 Flat washer...
- Page 19 Electric shearing Machine OPERATION MANUAL (Electric System) BRIEF INTRODUCTION This operation manual shows you the connection, use and maintenance for interface of electrical system and mechanism, and maintenance of Electric shearing machine. Before operation, please read the manual carefully, to avoid the damage of equipment and body.
- Page 20 IV: SETTING and OPERATION After the power, please operate the machine according to following steps: 1, Shearing operation 1). Turn the switch “SA4” to the single stroke position in the left. Step ↑↓ ↓↑↓↑ The motor will be stopped after once on the pedal switch, motor begin to work.
- Page 21 C. The foot switch is damaged, you have to replace it. 2. The machine continues working in single stroke state. The position of travel switch SQ2 is changed or damaged, you have to adjust it to the right position or replace it. 3.
- Page 22 Ⅵ. ELECTRICAL DRAWINGS...
- Page 32 Copyright © Huberts BV. All rights reserved.
Need help?
Do you have a question about the HU 1300 X 4 ES and is the answer not in the manual?
Questions and answers