Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Gotop Manuals
  4. GPS
  5. TLT-2H
  6. User manual

Gotop TLT-2H User Manual

Gps/gsm motorcycle tracker
Hide thumbs

Advertisement

Quick Links

Download this manual
User Manual
(TLT-2H GPS/GSM Motorcycle Tracker )

Advertisement

loading
Need help?

Need help?

Do you have a question about the TLT-2H and is the answer not in the manual?

Questions and answers

Related Manuals for Gotop TLT-2H

Summary of Contents for Gotop TLT-2H

  • Page 1 User Manual (TLT-2H GPS/GSM Motorcycle Tracker )
  • Page 2 Introduction 1． The TLT-2H GPS/GSM Tracker is a Vehicle Positioning Device what based on GPS and GSM/GPRS technology . It's can transmit the Longitude and Latitude coordinates to your Mobile Phone by SMS. And you can find the detail location of this unit on the Google Map or other Map Software.
  • Page 3 3.1. Specification MTK Case, support 900/1800(850/1900 can option) GSM module Support the TCP protocol GPS Chipset JRC chipset GPS sensitivity -164dB C/A Code 1.023MHz chip rate Channels 210 channel all-in-view tracking GPS frequency L1,1575.42MHz GPS Position Accuracy 2.5 meters, CEP GSM Position Accuracy Later will realize Velocity Accuracy...
  • Page 4 Red LED---indicate charge sate State Means constant Lighting charging No light charging was completed Green LED--- indicate the GPS signal state State Means No Lighting Working, but no location Flashing Working and has located Products Appendix ． 1）TLT-2H GPS/GSM Vehicle Tracker...

  • Page 5: Install Sim Card

    Installation Diagrame The external 5 wires of TLT-2H GPS/GSM tracker are as follows. Red for the 12V car power wire, connect to the car battery anode; Black for the earth GND, connect to the car battery cathode;...
  • Page 6 First Step, be the host of the unit, only the pre-saved number can receive the alarm message from the unit.but any number can send command to the unit to change the configuration of teh unit. Command as follows:...
  • Page 7 The Work Mode of TLT-2H TLT-2H have two work mode---SMS and GPRS Mode. If the users only need track the car by mobile phone, and check the position (latitude and longtitude) in Google Map, or control the oil and power by mobile phone, SMS Mode is enough.
  • Page 8 6660000 Explanation: When TLT-2H tracker receives the instruction and confirms the user password correctly, reads the GPS information. No matter whether effective, the information with the replying base station which is the set of the original software will be sent to the sender.
  • Page 9 Date: 2008-04-25 Time: 16:39:45 BS: 25ee0dff Fix: V ID: 353686009002030 STATE: SMS Note: If in the cold start and GPS no position, it will return to the void of information: eg: ERROR GPS GPRMC FRAME DATA BS: 27971054” ID: 353686009002030 STATE: SMS Display the location on map 1) Download Google earth software from...
  • Page 10 GPS tracker TLT-2H . Input the latitude and longitude that you receive from SMS and click on search button, the Google earth will display the location map for you. eg： You receive the information from the tracker. As follows: Lat: +22.50500 Long: +114.01000...
  • Page 11 2. Cut-off electricity and oil function 1. Open the cut-off electricity and oil function a. Command format: 900 + user password b. Confirm command format: 901 + user password c, Directly Command : 940+ user Password Note : 940=900+910 , the unit will implement this command at once after receive this command. Description: Due to the command with a certain degree of risk, so needs to do a more confirmation operation.
  • Page 12 Format: 777+new password (4 figures) +old password (4 figures) eg: 77712340000 Explanation: When TLT-2H tracker receives the SMS and confirm the user password correctly; changes the new user password to the old password. After set successfully, it will send the confirmation messages (SET USER PASSWORD OK) to the sender.
  • Page 13 Format: 100+ user password (4 figures) eg：1000000 Explanation: When TLT-2H tracker receives the instruction and confirms the user password correctly, it will close the GPS immediately, and send the confirmation messages (VIBRATION SENSOR ON OK) to the sender. The tracker built in vibration sensor, once monitors the track movement for change to open the GPS.
  • Page 14 Explanation: One of 3 telephone numbers stored in advance calls in, and hangs up after ringing 2-5 times, then the TLT-2H will send the location information to this number such as 4.1.6 to this number, the information state item automatically updates STATE: CALL. But other incoming numbers will automatically hang up.
  • Page 15 Electronic fence takes the set coordinates as the center, the set radius parameters to determine the scope of the fence. When open this feature, once the TLT-2H beyond the scope of the set fence, it will send location information as to 4.1.6 to the 3 preset numbers. The information state item automatically updates STATE: OS.
  • Page 16 corresponding coordinate form to set. In the demonstration, meanings of various parts are as follows: Edddmm.mmmm is longitude information with units of degrees and minutes, and the ddd expresses degree, mm.mmmm expresses minute (Accuracy for 4 after the decimal point, the following zero cannot bypass) Ndd.mmmm is latitude information with units of degrees and minutes and the dd expresses...
  • Page 17 Note : When this unit receive this command and confirm the password is right. And read the Update gps data whether is available. If ok, take the lat/log to the coordination, and the R for The Radius, and also pen the Geofence at the same time. If the configuration is ok. The unit Will send "set geo fence ok "...
  • Page 18 1) For Charge Description: TLT-2H check the state of ACC of the power through the ACC Cable,so the ACC ON when the car is moving, and the power of the car will recharge to the unit. and the ACC Off when the car is parking, and the power of the car will not recharge to the unit.
  • Page 19 After configuration of the alarm for moving is complete, if TLT-2H checking the ACC State is changed which from ACC ON to ACC OFF, after three minutes, the TLT-2H will take the current position for the coordiration point, the unit will open the defence(use the zzz.z) whether the GPS Data is Available or Valid .
  • Page 20 19. Updata on the Air 1). Formate : !-Password Eg: !-0000 Note: when TLT-2H receive this command and confirm the password is correct, the unit will restart and enter FTP Server to download procedure automatically.after succesful, the unit will restart again, and it's ok.
  • Page 21 N, at least is 1, at most is 50. When TLT-2H receive the command, and confirm the password is correct, then TLT-2H will send a feedback message to the sender what is SET GPS SAMPLING TIME AND QUANTITY OK .
  • Page 22 N product should meet greater-than-equal 60, that is T*N≥60. When TLT-2H receive the command, and confirm the password is correct, then TLT-2H will send a feedback message to the sender what is "GPRS REPORT SAMPLING 2 OK " . also will implement this command, then the unit will get the GPRMC data and save in the memory.
  • Page 23 3.1 Open the GPS instruction Format: 222+user password (4 figures) eg: 2220000 Explanation: When TLT-2H tracker receives the instruction and confirms the user password correctly, opens the GPS power. After the success, it will send the confirmation messages (GPS ON OK) to the sender.
  • Page 24 Explanation: When TLT-2H tracker receives the instruction and confirms the user password correctly, reads the GPS information. No matter whether effective, the information with the replying base station which is the set of the original software will be sent to the sender.
  • Page 25 Format: #801#user password#new user name## eg：#801#0000# username## Explanation: When TLT-2H tracker receives the instruction and confirms the user password correctly, changes the user name to the new user name. After the success, it will send the confirmation messages to the sender. The content is “CHANGE USERNAME OK”.
  • Page 26 Calling ON format: 151 + user password (4 figures) eg: 1510000 Explanation: When TLT-2H tracker receives the instruction to close calling and confirms the user password correctly, close the calling function (including the SOS, alarm when across the fence), after successfully, sent the confirm information "SET VOICE CALL: OFF" to the sender. When...
  • Page 27 Electronic fence takes the set coordinates as the center, the set radius parameters to determine the scope of the fence. When open this feature, once the TLT-2H beyond the scope of the set fence, it will send location information as to 3.1.5 to the 3 preset numbers. The information state item automatically updates STATE: OS.
  • Page 28 call the first user telephone number. If it is unsuccessful (closed or unable to connect or no response), makes vibration and starts calling the second and the third in turn. 1) Set the scope of the fence According to the input formats different of coordinates, user can choose the format as follows instructions to operate.
  • Page 29 When the tracker receives this instruction, judges to be authorized users and confirms the user password correctly, it will send the confirmation messages “SET GEO-FENCE OK” to the sender. Format 3 : 005+User Password Rzzz.z eg: 0050000R0.1 Note : When this unit receive this command and confirm the password is right. And read the Update gps data whether is available.
  • Page 30 Command : 210 + user password After set successfully, it will send the confirmation messages “GEO-FENCE OFF” to the sender. 15.Cut-Off Electricity And Oil Function a. Command format: 900 + user password b. Confirm command format: 901 + user password Description: Due to the command with a certain degree of risk, so needs to do a more confirmation operation.
  • Page 31 1) For Charge Description: TLT-2H check the state of ACC of the power through the ACC Cable,so the ACC ON when the car is moving, and the power of the car will recharge to the unit. and the ACC Off when...
  • Page 32 After configuration of the alarm for moving is complete, if TLT-2H checking the ACC State is changed which from ACC ON to ACC OFF, after three minutes, the TLT-2H will take the current position for the coordiration point, the unit will open the defence(use the zzz.z) whether the GPS Data is Available or Valid .
  • Page 33 21. Updata on the Air 1). Formate : !-Password Eg: !-0000 Note: when TLT-2H receive this command and confirm the password is correct, the unit will restart and enter FTP Server to download procedure automatically.after succesful, the unit will restart again, and it's ok.