Table of Contents
Summary of Contents for CEZA FSECZ102A
- Page 1 MY STOVE REMOTE APP QUICK CONFIGURATION This Document and its contents are the property of CEZA s.r.l. It may not be copied or disclosed to third parties without authorization. The company will protect their rights in accordance with the law.
- Page 2 FSECZ102A REMOTE Wi-Fi MODULE CEZA S.R.L. www.myceza.it...
-
Page 3: Table Of Contents
WARNINGS ....................1 RECOMMENDATIONS ................. 1 Cleaning: ....................1 Servicing: ....................2 TECHNICAL CHARACTERISTICS ..............2 FIRST FSECZ102A INSTALLATION GUIDE ............3 Static Cable: ................... 3 Mobile Connector: .................. 4 SIGN UP AND CONFIGURATION (ANDROID) ..........5 : ....................5 IRST STEPS “M... - Page 4 ............13 ELCOME TOVE ARE CONFIGURATED ’ ............13 ARNING HE STOVE ISN T CONNECTED ..... 14 ARNING OCATION ACCESS IS MANDATORY TO CONFIGURE A NEW STOVE ............14 ARNING RONG IFI STOVE NETWORK SIGN UP AND CONFIGURATION (IOS)............15 : ....................
-
Page 5: Summary
CEZA Ph2 board equipped with Remote Wi-Fi Module (FSECZ102A). it contains general information and instructions how to connect and configure the CEZA remote Wi-Fi module and My Stove Remote App. This guide does not contain descriptions and instructions for combustion system. -
Page 6: Servicing
Servicing: CEZA devices and accessories have been designed for long-life operation and don’t require special maintenance. However, in the case of malfunctions, CEZA s.r.l. strongly recommends that servicing be carried out by authorized trained personnel only. Technical characteristics Temperature range: -20°C to + 70°C (storage); -20°C... -
Page 7: First Fsecz102A Installation Guide
(Long side up/short side down) Use the rivets for fix the connector to the surface Right position Wrong position Connect the module FSECZ102A to the Static Connector in right position like in picture Right position Wrong position... -
Page 8: Mobile Connector
Mobile Connector: Make a hole on the side or rear of the stove, the hole must be as large as the 4-Pin connector. You can fix the connector in a parallel or perpendicular position to the floor Right position Wrong position Don’t expose the module to high temperature, it may damage the electronics... -
Page 9: Sign Up And Configuration (Android)
Sign up and Configuration (Android) First steps Power down the stove Connect the Wi-Fi module to the Ceza Motherboard (J7 black connector) Power on the stove Don’t disconnect ad reconnect module cable when power supply is on, it may damage the module. -
Page 10: Sign Up
Sign up When you start the App you’ll see this screen Click on “ ” SIGN UP Type your “Name” Type your “Surname” Type your “E-mail” Type your “Password” (must be with more than 6 numbers or characters) Click on “ ”... -
Page 11: Configuration: Stove Set-Up
Enable the location services (“security and position” settings in your Smartphone) Accept location permissions, when it requested by “Ceza My Stove Remote” App. Ensure the wifi network name isn’t composed by space characters (e.g.: “HOME 1” incorrect; “HOME1” it is OK) In the last Android versions, when you connect your smartphone to CEZASTOVE_AP…... - Page 12 Please agree to remain connected to CEZASTOVE_AP… network to finish the configuration wizard. The passage from “Step 4” to “Step 5” is automatic if the smartphone receives the IP address: 172.16.16.xx. You can find this information in “IP current” in the “Step 4”...
-
Page 13: Frequent Technical Issues (Android)
Frequent Technical Issues (Android) Setup failure The configuration don’t end with the Home page. Check the Wi-Fi networks in your smartphone settings: if you see the “ ” network, the CEZASTOVE_AP_XX… module is ready for configuration. Try again the Configuration: Stove Set-up. Ensure the Wi-Fi network Password is written correctly. -
Page 14: Reset Of The Wifi Module
Click on the My Stove Remote “Hamburger Menu” Click on “ ” CHANGE STOVE Click on “ ” ADD STOVE Reset of the WiFi Module If it is necessary to reset the wifi module, it is possible to make it in different manners and it depends to the “Type of Label”: 1st Version of Label without Reset button With this Type of Label, it is possible... -
Page 15: 2St Type Of Label With Reset Button
2st Type of Label with reset button With this Type of Label, is possible to make an AP MODE reset with the panel, or use reset button behind the left hole in the label, as in the photo Reset Button: •... - Page 16 Open the App. and type: stove name, wifi SSD name and password. Go in smartphone home page. Go to wifi settings. Keep pressed on wifi home network (it will appears a menu). Select “Forget network”. Connect the smartphone to CEZASTOVE_AP_XX. Open the App e press “Confirm”...
-
Page 17: Error Messages (Android)
Error Messages (Android) Warning: Check internet connection The smartphone is not connected to internet: ensure your smartphone is connected to the Wi-Fi network or mobile network (internet connection) and restart the APP. Warning: Error during login – try again Email and Password were not written correctly in the login page. -
Page 18: Warning: Location Access Is Mandatory To Configure A New Stove
Warning: Location access is mandatory to configure a new stove. This type of massage appears when you don’t accept the location permissions. Please check the settings in App entry of the your smartphone and enable the location permissions for app My Stove Remote. Warning: Wrong Wifi stove network This message appears when your smartphone isn’t connected with wifi module or the ip address is wrong... -
Page 19: Sign Up And Configuration (Ios)
Sign up and Configuration (iOS) First steps: Power down the stove Connect the Wi-Fi module to the Ceza Motherboard (J7 black connector) Power on the stove Don’t disconnect and reconnect module cable when power supply is on, it may damage the module. - Page 20 Click on “My Stove Remote” Click on “Get” When the download is finished, click on “Install” When the installation is finished, click on “Open”...
-
Page 21: Sign Up
Sign up When you start the App you’ll see this screen Click on “ ” SIGN UP Type your “Name” Type your “Surname” Type your “E-mail” Type your “Password” (must be with more than 6 numbers or characters) Click on “ ”... -
Page 22: Configuration: Stove Set-Up
Enable the location services (“security and position” settings in your Smartphone) Accept location permissions, when it requested by “Ceza My Stove Remote” App. Ensure the wifi network name isn’t composed by space characters (e.g.: “HOME 1” incorrect; “HOME1” it is OK) When you connect your Iphon to wifi module, wait a blue flag like the picture below. - Page 23 You can find this information in “IP current” in the “Step 4” of the configuration wizard. If the IP is different from 172.16.16.xx the passage from “Step 4” to “Step 5” will be blocked. In this case you can check the connection between Smartphone and CEZASTOVE_AP…...
-
Page 24: Frequent Technical Issues
Frequent Technical Issues (iOS) Setup failure The configuration do not end with the Home page. Check the Wi-Fi networks in your smartphone settings: if you see the “ ” network, the CEZASTOVE_AP_XX… module is ready for configuration. Try again the Configuration: Stove Set-up. -
Page 25: Reset Of The Wifi Module
Click on “ ” CHANGE STOVE Click on “ ” ADD STOVE Reset of the WiFi Module If it is necessary to reset the wifi module, it is possible to make it in different manners and it depends to the “Type of Label”: 1st Version of Label without Reset button With this Type of Label, it is possible... -
Page 26: 2St Type Of Label With Reset Button
2st Type of Label with reset button With this Type of Label, is possible to make an AP MODE reset with the panel, or use reset button behind the left hole in the label, as in the photo Reset Button: •... -
Page 27: Error Messages (Ios)
Error Messages (iOS) Warning: Check internet connection The iPhone is not connected to internet: ensure your iPhone is connected to the Wi-Fi network or mobile netwotk (internet connection) and restart the APP. Warning: Error during login – try again Email and Password were not written correctly in the login page. -
Page 28: Warning: Location Access Is Mandatory To Configure A New Stove
Warning: Location access is mandatory to configure a new stove. This type of massage appears when you don’t accept the location permissions. Please check the settings in App entry of the your smartphone and enable the location permissions for app My Stove Remote. Warning: Wrong Wifi stove network This message appears when your smartphone isn’t connected with wifi module or the ip address is wrong...