quiko QK-CE220CN User Manual

QK-CE220CN
Control board for 230V gearmotors
USER MANUAL V01
ON
1 2 3 4 5 6
7 8 9 10
L2 L3
ANT
PROG
PROG
RADIO
TIME
P2
P1
T2
POWER
SLOW
STOP
L5
L9 L6
L7
L4 L8
PED PH2 PH LSO LSC
START M
LSC
PH2
START PED
STOP 24Vac
PH LSO
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
N.C.
N.C.
N.C.
N.C.
COM
N.O. N.O.
N.C. COM
Terminal Tip. Description
1 - 2com NO START CONTACT (Each impulse OPEN/STOP/CLOSE/STOP)
3 - 2com
NO PEDESTRIAN CONTACT
4 - 6com NC
SAFETY BAND OR OPENING PHOTOCELLS (If no use make bridge)
5 - 6com NC CLOSING PHOTOCELLS (If no use make bridge)
7 - 6com NC STOP contact(If no use make bridge)
9 - 8com NC LIMIT SWITCH OPENING
10 - 8com NC LIMIT SWITCH CLOSING
11 - 12 24V ~ Power service or accessories (output 24Vac 250mA)
13-14-15 230V ~ Input ENGINE (13-14 input phases with capacitor in parallel) (15 common)
16 - 18 230V ~ FLASH
17 - 18 230V ~
COURTESY LIGHT
19 - 20 230V ~ Input POWER 110Vac
21 - 22 / GROUND
23 - 24 Input ANTENNA ( 24 signal)
Example wiring selector
L1
2 1
CONTACT
NO
Start
FUSE
Example wiring photocells
BLK COURT 230Vac
5 6
+ -
NC COM
RX
UNI
Our products if installed by qualified personnel capable to evaluate
EN risks, comply with norms UNI EN 12453, EN 12445
The CE mark complies with EEC European directive 89/336
+ 93/68 D.L.04/12/1992 n.476
7 6
CONTACT
NC
Stop
11 12
+ -
TX

TECHNICAL SPECIFICATIONS

Power 230V AC +/- 10%
Power engine 550 W
Output accesories 24V AC 250mA
Time for automatic close 5 a 120 sec
Time for maneuver
3 a 120 sec
Time for slow down 2 a 120 sec
Time for courtesy light
180 sec
Nr codes storable 254 code
Transmitters type
Fix\Roll-code
Frequency 433.92 / 868 Mhz
Temperature to work -20 a 70°C
Sensibility Better of –100dBm
Homologation Conf ETS 300-220/ETS 300-683
TRIMMER T1
The trimmer POWER regulates the torque and sensitivity during the maneuver
TRIMMER T2
The trimmer POWER SLOW regulates the torque and sensitivity during SLOW DOWN phase
-
+
The TORQUE increases turning the trimmer in clockwise sense.
BUTTON P1
o r R A D I O P R O G f o r s t o r a g e t h e t r a n s m i t t e r
BUTTON P2
o r P R O G T I M E f o r s t o r a g e t h e s t r o k e

ENCODER OPERATION

Actived by DIP8 ON
CHANGE OF SENSITIVITY AND TORQUE
More torque = less sensitivity
Less torque = more sensitivity
The parameters are set by the trimmer T1 and T2.

TABLED LEDS

L1 Led STATUS Lit when the unit is powered
L2 Led RADIO Lit when accessing in radio storage
L3 Led PROG. TIME It is blinking when in programming
L4 Led START Lit when taking a pulse
L5 Led PEDESTRIAN Lit when taking a pedestrian pulse
L6 Led PHOTOCELLS Lit when the fotocells are aligned
L7 Led L.S. OPENING Lit when limitswitch opening is on NC
L8 Led L.S. CLOSING Lit when limitswitch closing is on NC
L7+L8 Led STOP
Both on when the stop is on NC
L9 Led PHOTOCELLS Lit when the photocells are aligned/
AP/ safety edge
safety edge connected