Table of Contents
Advertisement
Quick Links
John Lewis
House Equate Single Cupboard
Stock number: 84982002
Thank you for purchasing this House Equate single cupboard. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this product
Pre-assembly preparation
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer
from whom you bought this product.
TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 45 MINUTES to assemble with 1 PERSON.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Please assemble on a soft clean surface to avoid damages to your product
Advertisement
Table of Contents
Related Manuals for John Lewis House Equate Single Cupboard
Summary of Contents for John Lewis House Equate Single Cupboard
- Page 1 John Lewis House Equate Single Cupboard Stock number: 84982002 Thank you for purchasing this House Equate single cupboard. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product Pre-assembly preparation Necessary Tools Please check the pack contents before attempting to assemble this product. A full checklist of components is given in this leaflet.
- Page 2 Fittings checklist Cam stud Hinge Hinge/KD block screw12mm Wood dowel Cover caps Plinth fixing screw KD block 50 mm Nail glides...
-
Page 3: Parts Checklist
Parts checklist Top panel Back panel Left side panel Front/Back plinth Right side panel Left/Right plinth Shelf Bottom panel Door... - Page 4 Step by step assembly instructions Step One Insert four cam studs (A) into the allocated holes in the top panel (1) and tighten clockwise with a crosshead screwdriver. Make sure the cam studs are fixed in a right angle and do not overturn. Step Two Insert four cam studs (A) into each of the two side panels (2+3) as shown, and tighten clockwise with a crosshead screwdriver.
- Page 5 Step Three Insert two wood dowels (C) into each end of the bottom panel (9) and into each end of the shelf (4). Note: Make sure the wooden dowels are inserted into the blind holes, and not into the cam stud holes at the end of the panel.
- Page 6 Step Five Gently slide the back panel (6) into the grove in the side panel (2) and bottom panel (9) as shown. Step Six Connect the right hand side panel (3) to the shelf and bottom panel, then insert 4 cams (B) into the allocated holes and tighten the cams clockwise with a screwdriver.
- Page 7 Step Seven Now connect the top panel (1) to the side panels. Then insert 4 cams (B) into the allocated holes in the side panels, and tighten gently clockwise with a screwdriver. Do not overturn. Step Eight Ensure that the cabinet is in a 90-degree straight angle, then slide three KD blocks (D) into the grove in the side panels/bottom as shown.
- Page 8 Step Nine Lay the two front/back plinths (7) and the two left/right hand side plinths (8) out on your protected working surface as shown. Insert four cam studs (A) into the allocated holes in the front/back plinths (7), and tighten clockwise with a crosshead screwdriver. Do not overtighten. Then insert two wooden dowels into the center top holes in the front/back plinths (7), and four wooden dowels into the ends of the side plinths (8).
- Page 9 Step Eleven Insert four cams (B) into the allocated holes and tighten gently clockwise with a screwdriver. Do not overturn. Step Twelve With eight 50 mm screws (I), fix the plinth to the bottom panel and tighten the screws clockwise with a crosshead screwdriver.
- Page 10 Step Thirteen Lay the door down as shown and fix the two hinges (H) with 12 mm fixings screws (G). The screws are tightened clockwise with a crosshead screwdriver. Finally tap the four nail glides (E) onto the corners of the plinth. Step Fourteen Finally attach the cover caps (H) to the cams as shown.
-
Page 11: Door Adjustment
Door adjustment Please follow these simple steps for door adjustment: In or out adjustment: Loosen the rear hinge screw anticlockwise, and gently move the hinge in or out to the required position. Re-tighten the adjustment screw by turning clockwise. Sidewise adjustment: Turn the forward adjustment screw clockwise or anticlockwise for sidewise adjustment of the door. -
Page 12: Care And Maintenance
Care and Maintenance How to care for your furniture Furniture with a melamine surface should be dusted with a dry cloth. Spray polishes are best avoided as they contain silicones which may spoil the furniture’s surface by building up over time. Make sure all surfaces are protected from heat and liquids by mats and coasters.