MasterForce 260-9518 Operator's Manual

MasterForce 260-9518 Operator's Manual

1150 peak amp jump starter, ac/dc/usb power source and compressor

Advertisement

1150 Peak Amp Jump Starter,
AC/DC/USB Power Source
and Compressor
260-9518
To Reduce The Risk Of Injury, User Must Read And
Understand Operator's Manual. Save These Instructions For Future Reference.
0099002192-01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 260-9518 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MasterForce 260-9518

  • Page 1 1150 Peak Amp Jump Starter, AC/DC/USB Power Source and Compressor 260-9518 To Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference. 0099002192-01...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Safety Symbols ................Page 3 Safety Information ................Page 4 Important Safety Instructions ............Page 5 Personal Safety Precautions............Page 6 Charging the Internal Battery of the Jump Starter .......Page 6 Operating Instructions ..............Page 7 Maintenance Instructions ............Page 10 Moving and Storage Instructions ..........Page 10 Troubleshooting ................Page 10 Specifications ................Page 11 Replacement Parts ...............Page 11...
  • Page 3: Safety Symbols

    SAFETY SYMBOLS Some of the following symbols may be used on your jump starter. Please study them and learn their meaning. Proper interpretation of these symbols will allow better and safer operation of the jump starter. Symbol Name Designation/Explanation Volts Voltage Amperes Current...
  • Page 4: Safety Information

    SAFETY INFORMATION The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger. The instructions and warnings they give are no substitutes for proper accident pre- vention measures.
  • Page 5: Important Safety Instructions

    1. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. 1.7 Place the jump starter as far away from the battery being jumped as the cables will permit. RISK OF EXPLOSIVE GASES. 1.8 Do not expose the jump starter to rain or snow. WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS.
  • Page 6: Personal Safety Precautions

    2. PERSONAL SAFETY PRECAUTIONS 2.1 Restrictions on Use: The inverter 2.4 If battery acid comes in contact with may not be used with life support eyes, flush eyes immediately for a devices or systems. Failure of this minimum 10 minutes and get medi- inverter can reasonably be expected cal attention.
  • Page 7: Operating Instructions

    3. Insert the other end of the accessory 4. Monitor the progress of the charge by cable into the vehicle’s accessory out- pressing the Select button until the let (lighter socket). Battery % LED lights. When the bat- tery is fully charged, disconnect the NOTE: The Battery % LED does not oper- accessory cable from the jump starter ate during this method of charging.
  • Page 8 NOTE: Do not power a 12V device with the NOTE: To protect your electronic devices, unit while charging the internal battery. the USB will automatically shut off when the internal battery’s charge is low. 1. Make sure the device to be powered is OFF before inserting the 12V DC acces- USING THE AIR COMPRESSO sory plug into the 12V DC accessory...
  • Page 9 USING THE INVERTER IMPORTANT: This inverter uses a modi- fied sine waveform, which is not quite the It is important to know the continuous same as power company electricity. For wattage of the device you plan to use with the following devices, we strongly recom- the inverter.
  • Page 10: Maintenance Instructions

    5. MAINTENANCE INSTRUCTIONS • After use and before performing main- • Ensure that all of the jump starter tenance, unplug and disconnect the components are in place and in good jump starter. working condition. • Use a dry cloth to wipe all battery •...
  • Page 11: Specifications

    PROBLEM POSSIBLE CAUSE SOLUTION The unit won’t power my The 12V device is not Turn on the 12V device. 12V device. turned on. The Portable Power’s Check the battery charge battery is not charged. status by pressing the button on the front of the unit.
  • Page 12: Warranty

    ® discretion, MASTERFORCE™ agrees to have the item or any defective part(s) repaired or replaced with the same or similar MASTERFORCE™ product or part free of charge, within the stated warranty period, when returned by the original purchaser with original sales receipt. Not withstanding the foregoing, this limited warranty does not cover any damage that has resulted from abuse or misuse of the Merchandise.
  • Page 13 NOTES Page 13...
  • Page 14 NOTES Page 14...
  • Page 15 NOTES Page 15...
  • Page 16 © 2020 Menard, Inc., Eau Claire, WI 54703 05/2020...

Table of Contents

Save PDF