Related Manuals for 3form SimpleSpec 200.08
Summary of Contents for 3form SimpleSpec 200.08
- Page 1 To Go SimpleSpec 200.08 Installation Manual For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
-
Page 2: Contents Overview
Suspend Anchoring KIT Wood Insert bolt Anchor Anchor rod, 50mm rod, 25mm 3-15-7000-K 3-15-0791 3-15-0734 3-15-3011A 3-15-3032A 3-15-1754 For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved. - Page 3 (×2) Suspend Anchoring KIT 3-15-7000-K Stainless Steel: 3-15-2001 (×1) 1" Shelf Holder KIT (SS: 3-15-0754-K; bo: 3-15-2018) Black Oxide: 3-15-2003 For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 4 Overview The 200.08 partition comes from the 3form Suspend Hardware System. This is a suspended side-fastening partition for concrete and wood with smooth connectors and a Drop Ceiling cover. This elegant solution would be a great addition to any space.
- Page 5 With screw in anchor (3-15-311A), use a deep. bulb or with compressed air. hammer to insert anchor. For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 6 Insert the metal pull ring. channel through the drilled hole into the wall cavity. For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 7 Drill Ø7/16" (Ø11.1mm) hole, minimum Use an Allen wrench to install the m8 20mm deep. Threaded Insert (3-15-791). For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 8 Attach the Cable Tensioner (SS: 3-15-1636; bo: 3-15-2005) to the floor anchor with the included m8 Threaded rod (3-15-1754). For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 9 Maximum Tension = 400 lbs exit on the tensioner. Hollow Substrate: Max Tension + Weight < 70lbs For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 10 Installation Manual Installation Dry-Fit Panel and Measure Do not tighten set screws! Do not tighten set screws! For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 11 To Go SimpleSpec 200.08 Installation Manual Installation Dry-Fit Panel and Measure cont... Do not tighten set screws! For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 12 To Go SimpleSpec 200.08 Installation Manual Installation Dry-Fit Panel and Measure cont... remove Panel For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 13 Tighten set screws to the cable (top side brackets only). 6" max For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 14 Allen wrench through tensioner as shown in 6c. 4" For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
- Page 15 Cut cable and put a drop of super glue at end of cut cable to keep from fraying. For more information, please visit 3-form.com or call 800.726.0126 November 2019 | mAN-rTG-200-08 | rev 003 © 2019 3form, Inc. All rights reserved.
Need help?
Do you have a question about the SimpleSpec 200.08 and is the answer not in the manual?
Questions and answers