Kichler Lighting SOUTH HOPE Manual

SOUTH HOPE #49473
INSTALLATION
1. Installing the glass
a. To install glass for the Lyndon Lantern
Item #49500:
• Hold the glass so the opening is facing up.
• Place the glass over the LED.
• Use the three screws to hold the glass in
place. Do NOT over tighten the screws.
b. To install glass for the South Hope Lantern
Item#49473:
• Hold the glass so the opening is facing down.
• Place the glass over the LED.
• Gently rotate the glass clockwise until it will not
move anymore. Carefully pull up on the glass to
ensure it has properly engaged with the lantern.
2. Charging the lantern
For best results, completely charge the lantern prior
to use.
• To charge the lantern, plug the charger into the
wall.
• Attach the other end of the charger into the
dedicated port on the bottom of the lantern.
• A red indicator light will illuminate to illustrate the
lantern is charging. Once the battery is complete
ly charged, this light will become green.
NOTE: The lantern can still operate as a light and/or
speaker while it is being charged.
3. Turning the light ON/OFF
• Tap the power button
to turn the light on.
The light will come on and the switch itself will
also illuminate green
• Tap the power button again to turn the light off.
The light will turn off and the green switch will no
longer be illuminated.
4. Dimming the lantern
• The lantern defaults to 50% light output when
first turned on.
• To adjust the light output, press and hold the
power button. This will begin to dim the light to
its lowest position. Release the button when the
desired light output is reached; otherwise the
lantern will continue to its lowest light output.
• After the lantern has reached its lowest light
output, release then hold the power button again
to increase light output.
• Continue to hold the power button to get to the
highest output level or release the button when
the desired light output is reached.
Date Issued: 03/17/17
PORTABLE LANTERN
GLASS
SCREW
LED
CHARGING PORT
SEE OTHER SIDE FOR CANADIAN FRENCH TRANSLATIONS.
VOIR L'AUTRE CÔTÉ POUR LES CANADIENS TRADUCTIONS
EN FRANÇAIS.
We're here to help
LYNDON #49500
SCREW
LED
5. Pairing and connecting a BLUETOOTH phone/
tablet
• Press and hold the Bluetooth button until a
tone is heard. The button will flash blue
signaling it is ready to pair.
• Turn on the Bluetooth function on your
phone/ tablet.
• Using the Bluetooth settings of your phone/
tablet, select "Kichler" from the list of avail
able connections.
• The Bluetooth indicator light on the lantern
will change to solid blue when the connection
is successful and another tone will sound.
• To play music on your lantern, ensure volume
on your phone/tablet is NOT set to mute.
• To adjust the listening volume, use the
volume controls on your phone/tablet.
6. Listening to music
• After you phone/tablet has paired with the
lantern, it will connect automatically. If the
lantern does not connect automatically,
repeat the pairing process to register your
phone/tablet.
• The audio source (phone/tablet) will control
the volume, pause, play, and advance tracks.
NOTE: If sound is NOT inaudible, ensure your phone/
tablet is not muted and make sure the volume is at
an appropriate level.
7. Turning off the lantern's Bluetooth audio
• To turn off the lantern's Bluetooth audio
function, hold the Bluetooth button
until a tone is heard and the blue light on the
Blue tooth button is no longer lit.
8. How to switch audio source (changing between
a different phone/tablet)
• Repeat pairing instructions (see section titled
Pairing and connecting a BLUETOOTH
phone/tablet) on second phone/tablet.
• If primary phone/tablet is already connected,
press and hold Bluetooth button until blue
light flashes. Ensure, primary phone/tablet is
disconnected.
• Select lantern (titled Kichler) on second
phone/tablet.
866-558-5706
Hrs: M-F 9am to 5pm EST
GLASS
INDICATOR LIGHT
IS-49500-CB