Texmate CL-B101D40PS Manual

LEOPARD
FAMILY

Specifications

Input Specs: ������������������ Depends on Input signal conditioner
A/D Converter: �������������� 14 bit single slope
Accuracy: ���������������������� ±(0�05% of reading + 2 counts)
Temp. Coeff�: ����������������� 100 ppm/°C (Typical)
Warm up time: ��������������� 2 minutes
Conversion Rate: ���������� 10 conversions per second (Typical)
Digital Display: �������������� 4 digit 0.56" LED red (std), green (optn)
Range -1999 to 9999 counts�
Bargraph Display: ��������� 101 segment 235º circular red (standard),
Green (optional) or tricolor (optional) LED�
Polarity: ������������������������� Assumed positive� Displays - negative
Decimal Selection: �������� Front panel button selectable, X•X•X•X•
Positive Overrange: ������ Bargraph and top segments of digital display
flash�
Negative Overrange: ���� First segment of bargraph and bottom seg-
ments of digital display flash�
Relay Output: ���������������� Two 9 Amp Form C relays, two 4 Amp Form
A relays or 4 x 4 Amp Form A relays
Analog Output: ������������� Isolated 16 bit user scalable mA or V
OIC (mA out) �������������� 4-20 mA @ 0 to 500٠max loop resistance
OIV (volts out) �������������� 0-10 V DC @ 500 ٠or higher resistance
Power Supply: ��������������� AC/DC Auto sensing wide range supply
PS1 (std) �������������������� 85-265 VAC / 95-300 VDC, 50-400Hz 4.2W
PS2 ����������������������������� 18-48 VAC / 10-72 VDC, 50-400Hz 4�2W
Operating Temp�: ���������� 0 to 50°C
Storage Temp: ��������������� -20°C to 70°C
Relative Humidity: �������� 95% (non condensing)
Case Dimensions: �������� Bezel (4.48"x4.48") 113.8x113.8mm
Depth behind bezel (4.23") 107.46 mm
Plus (0�48") 12�24 mm for connectors
Weight: ��������������������������� 16 oz�, 1lb 4 oz when packed
Bargraph Center Point Display Mode Selection . . 7
Bargraph Color Programming Mode . . . . . . 10
Case Dimensions. . . . . . . . . . . . . . . . . . . . . . . 8
Component Layout . . . . . . . . . . . . . . . . . . . . 12
Connector Pinouts . . . . . . . . . . . . . . . . . . 11-12
Controls and Indicators . . . . . . . . . . . . . . . . . 2
Decimal Point and Brightness Selection . . . . 6
Digital Span Selection for Bargraph Display . 6
CL-B101D40PS Manual (d0096)
Smart 101 segment, 4 digit LED Tricolor or Mono-color
digital bargraph controller with Programmable Scale
Factor input signal scaling and four fully programmable
monitoring, measurement, and control applications.
0.56" LEDs

Table of Contents

Digital Span Selection for Analog Range Output . 7
Functional Diagram . . . . . . . . . . . . . . . . . . . . 11
General Features . . . . . . . . . . . . . . . . . . . . . . . 1
I-Series Input Signal Conditioning Modules . . 13-15
Input Module Calibration Procedures . . . . . 17
Input Module Component Glossary . . . . . . . 16
Ordering Information . . . . . . . . . . . . . . . . . . . 19
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . 11
CL-B101D40PS
set points in a switchboard style case for

General Features

• External transmitters or signal conditioners can be eliminated by
direct connection of the sensor output to more than
40 Plug-in Input Signal Conditioners that include:
- AC/DC Current
- AC/DC Voltage
- Load Cell
• Optional isolated 16 bit analog output. User or factory scalable to 4
to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span
from ± one count to the full scale range of - 1999 to 9999 (12000
counts).
• A Programmable Tricolor (Red-Green-Orange) or mono color (red or
green), 101 segment high brightness bargraph.
• Red 4-digit LED display with a range of -1999 to 9999
(12000 counts). Optional green digital display.
• Front panel LED annunciators provide indication of setpoint status.
• Two 9 Amp Form C, and two 4 Amp Form A or 4 x 4 Amp Form A
relays available.
• Auto-sensing AC/DC power supply. For voltages between
85-265 V AC / 95-300 V DC (PS1) or 18-48 V AC / 10-72 V DC
(PS2).
• 24 V DC excitation is available to power external 4/20mA
transmitters and 5 or 10 V DC excitation is available for
resistance bridge type sensors.
• Provision to connect an external programming lockout switch.
• Provision for external DIM switch to reduce the brightest
display setting by 50%.
• Automatic intelligent averaging, smooths noisy signals while
providing a fast display response to real level changes.

Software Features

• The bargraph can display, full
scale, any desired portion of
the digital reading.
• Setpoint 1 has delay-on-make
and delay-on-break plus
a special "pump on pump
off" mode that creates a
Hysteresis Band between SP1
and SP2.
Programming Conventions . . . . . . . . . . . . . . . 2
Setpoint Setting & Relay Conf. Mode . . . . 9-10
Software Features . . . . . . . . . . . . . . . . . . . . . . 1
Software Logic Tree . . . . . . . . . . . . . . . . . . . . 3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 1
Successive Digital Rescaling. . . . . . . . . . . . . . . . . . . .5
Two Point Analog Range Setting & Calibration. . . 8
- Pressure - Resistance
- Process - Temperature
- Prototype - 4 to 20 mA
• Four programmable setpoints
with adjustable Hysteresis.•
Bargraph center zero function.
• Relay activation can be select-
ed to occur above (hi) or below
(Lo) each setpoint.
• Digital display blanking.
• Decimal point setting.
• Four-level brightness control
Page 1