Advertisement
Available languages
Available languages
26737 Speaker stand
»Ring Lock«
- Attractive stand thanks to its elegant design for tight spaces
- For loudspeakers up to max. 20 kg*
- With a patented mandrel for secure and tight fitting speakers.
- Height adjustable stand tube combinatio
-
(with locking pin and clamp screw)
- Height min. 1120 / max.1820 mm; Heavy cast iron base ø 450 mm,
-
Mandrel ø 35-36.5 mm; Extension: ø 35 mm; Weight: 11.3 kg
Thank you for choosing this product. The instructions provide directions to all of the
important set up and handling steps. We recommend you keep these instructions for
future reference.
SAFETY NOTES
A. GENERAL
A.
- Load bearing weight: max 20 kg*
A.
- Assembly and handling only by qualified technicians
A. -
(we recommend 2 technicians that are physically fit)
A.
- Prior to installation check if the stand, loudspeaker (particularly the size
A. -
and quality of the flange adapter) as well as ensuring that the aids
A. -
(e.g. ladders) are in working order
A.
- Wear protective gloves during assembly
A.
- Only to be used indoors
A.
- Be sure that the surface will bear the load and is suitable and level
A.
- ATTENTION! The base plate is very heaving and improper use
A. - ATTENTION!
can result in risk to individuals and objects
A.
NOTE: In particular during assembly do not drop or crush limbs
B. SETUP, OPERATION, DISASSEMBLY
B.
SETUP The screw connection between the stand tube and
B. -
the base plate must be screwed in as far as it will go 3.a
B.
- Routinely check that the screws are properly tightened
B.
OPERATION: The weight tube combination must be centered:
B.
- if the weight is not centered - this has a negative affect on stability
B.
- Locking pin 13 must be locked into place
B. -
and the clamping screw 14 must be tightened
B.
- Never loosen the locking pin and the clamp screw
B. -
without having someone hold the
B. -
heavy objects on the stand 7
B.
DISASSEMBLY: first remove the objects from the extension tube
B.
then unscrew the stand tube from the base plate
C. LATERAL FORCES
C.
- Lateral forces are to be avoided due to the risk of it falling over
C. -
These lateral forces are created (often unintentionally) as follows:
C. -
a. the load bearing weight is not centered
C. -
b. bump and/or brushing into, vibration, wind, uneven surface
C. -
c. the attempt to move the loaded stand
C.
NOTE: Maintain safety distance, keep unauthorized persons away
C.
Should the effectiveness of the measures not be guaranteed,
C.
(.g. through not keeping the safety distance and the distance is not
C.
routinely checked by personnel) the technicians should secure the object
C.
with the following additional steps these include among others:
C.
- anchor the base plate to the floor
C.
- suitable extension/expansion/weighting down of the base plate
FAULT-FINDING (F) and
REPAIR (R)
F: The base plate rocks back and forth on the floor:
F:
R: Check if the surface is even
F:
R: Are the felt protectors there?
F: The tube combination is not sturdy i.e. is
F:
leaning to one side:
F:
R: Check to ensure that the M-20 bolt is tight,
F: R:
Securely screw in the tube combination 3.a.
F:
R: Check to ensure the tube combination is
F: R:
straight
F:
R: Ensure that the surface is even
F: Distance rod is not stable / retracts:
F:
R: Tighten the clamping screw 14
F:
R: Check locking pin 13 to see if it is clicked
into place
F: It is difficult to turn the loudspeaker
F:
R: Pick up the loudspeaker a bit when turning
F: R:
the loud speaker
F:
R: Loosen the locking pin 4 somewhat
* With centric loading, on a horizontal surface and without lateral forces (wind, shocks etc.)
SET UP INSTRUCTIONS
1 Base plate with feet are to be placed
1
feet down in the desired position.
2 Screw the clamp screw into clamping
2
bracket and tighten (manual strength is
2
enough).
3 Threaded connector M20 of the tube
3
combination is to be screwed into the
3
baseplate as far as it will go.
3.a Ensure that a space is not left between
3.a
the tube and the plate. NOTE: Regularly
3.a
check and tighten the screws, if needed.
CHECK, MAINTENANCE, CLEANING
- Careful use of the stand maintains the use of the telescope and the load bearing functionality of the stand, as well as the
-
safety of the installation.
- Perform workstation maintenance only without the speakers attached and watch for possible risks (pinched hands/fingers,
-
impact or the stand falls over).
- To care for the product use a damp cloth and a non-abrasive cleaning agent.
TECHNICAL DATA
Base plate: Gray die cast, powder coated black
Tube combination: Steel, powder coated black
Adjustment ring: Aluminum anodized, black
Material
Threaded bolt: Steel, galvanized
Telescope bracket: Zinc Die-cast, powder
coated black
Handle, mandrel, adapter: PA-6
Load
max. 20 kg*
Weight
11.3 kg
Floor base plate ø 450 mm,
Dimensions
Height: 1120-1820 mm
Plate: 460 x 460 x 25 mm
K&M Carrying case: 21421 for 2 rods,
K&M Carrying case:
K&M-Flange adapter: 19580, 19654, 19656
Accessories
K&M-Screw-on flange: 24281
K&M-Adapter Sleeve: 21326 for loudspeakers
with 38 mm internal diameter (=US-Variant)
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
26737-000-55 Rev.12 03-80-832-00 3/20
26751 for 1 base
Advertisement
