Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
NI WSN-3295 Outdoor IP Enclosure
For the NI 9792 WSN Real-Time Gateway
This installation guide describes how to install and use the National Instruments WSN-3295 outdoor IP
enclosure. The NI WSN-3295 outdoor IP enclosure is an accessory that provides the NI 9792 WSN
Real-Time Gateway with a minimum ingress protection (IP) rating of IP65 against dust and water in
harsh outdoor or industrial environments. For more information about IP ratings, refer to the
Understanding IP Ratings
Real-Time Gateway User Guide and Specifications available at
Figure 1 shows the NI WSN-3295 outdoor IP enclosure components.
2
1
14
1
Antenna IP Sleeve
2
2.4 GHz Antenna
3
Antenna IP Boot
4
Lock Nuts
5
Gland Shells
6
Gland Inserts, Reduced
Note
You need a #1 and a #2 Phillips screwdriver to install the NI WSN-3295.
section. For the NI 9792 device specifications, refer to the NI 9792 WSN
3
13
12
7
Gland Inserts, Standard
8
Gland Plugs
9
Ethernet Field Termination
Connector Kit
10 Ethernet Interface Connector
11 Internal RJ45 Ethernet Cable
Figure 1. NI WSN-3295 Outdoor IP Enclosure Components
ni.com/manuals
4
10
11
12 Internal Antenna Cable Connector
13 No-Crimp Ethernet Plug
14 4-40 Screws
— Quick Release Latches on
Enclosure (not shown)
.
5
6
7
8
9
Advertisement
Table of Contents
Related Manuals for National Instruments WSN-3295
Summary of Contents for National Instruments WSN-3295
- Page 1 This installation guide describes how to install and use the National Instruments WSN-3295 outdoor IP enclosure. The NI WSN-3295 outdoor IP enclosure is an accessory that provides the NI 9792 WSN Real-Time Gateway with a minimum ingress protection (IP) rating of IP65 against dust and water in harsh outdoor or industrial environments.
- Page 2 Figure 2 shows the NI WSN-3295 dimensions. Caution When mounting the NI WSN-3295, allow at least 72.6 mm (3 in.) of clearance next to the enclosure quick release latches so you can open the enclosure if needed. NI WSN-3295 Outdoor IP Enclosure Installation Guide...
- Page 3 Figure 2. NI WSN-3295 Dimensions Setting Up and Installing the NI WSN-3295 Complete the following steps to set up and install the NI WSN-3295. Step 1: Unpack and Inspect the Kit Contents Remove the device from the package and inspect the device and kit contents. Contact NI if the device appears damaged.
- Page 4 Complete the following steps to install the NI 9792 WSN Real-Time Gateway: Open the quick release latches on the NI WSN-3295 cover. The NI WSN-3295 ships with an installed internal mounting plate. Remove the plate by unscrewing the 10–32 screws.
- Page 5 Step 4: Assemble Glands The NI WSN-3295 ships with two different insert sizes to use with the included gland shells. The larger insert can accept cables with a diameter from 4–8 mm, while the smaller insert can accommodate cables from 2–6 mm. For the larger 4–8 mm insert, NI recommends the Ethernet cable (NI part number: 182219-05) and the power cord (NI part number: 780703-01) available from ni.com...
-
Page 6: Step 5: Install The Antenna
Screw the antenna onto the external antenna connector until it bottoms out. Slide the IP sleeve down the antenna and over the IP boot until the IP sleeve touches the enclosure. NI WSN-3295 Outdoor IP Enclosure Installation Guide ni.com... - Page 7 Step 6: Mounting the NI WSN-3295 Figure 6 shows the NI WSN-3295 mounting hole dimensions, which are molded on the enclosure back surface for convenience. NI recommends installing the NI 9792 WSN Real-Time Gateway before mounting the NI WSN-3295, as shown in Figure 3.
- Page 8 Tighten the outer compression nut to approximately 2.50 N · m (22.1 lb · in.) to seal the cable. Attach the external Ethernet field termination cable to the NI WSN-3295 Ethernet interface connector on the outside of the NI WSN-3295.
-
Page 9: Step 8: Attach The Cover
Step 8: Attach the Cover The cover of the NI WSN-3295 is equipped with quick release latches (not shown). You can prevent tampering with the enclosure contents by placing a lock through the holes in the quick release latches. Figure 8. Attaching the NI WSN-3295 Cover ©... -
Page 10: Environmental Limitations
NI recommends accounting for these limitations when using the NI WSN-3295. • The NI WSN-3295 is rated for an external ambient of 60 ºC when in use with the NI 9792 WSN Real-Time Gateway. Exceeding this temperature could damage the NI 9792 WSN Real-Time Gateway internal components. - Page 11 If you want to use the second Ethernet connection and maintain your IP rating, you need to use the no-crimp Ethernet plug included with the NI WSN-3295 to build an Ethernet cable for the second connection. Complete the following steps to use the no-crimp Ethernet plug: Run your Ethernet cable through the glands into the NI WSN-3295.
-
Page 12: Environmental Management
National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. National Instruments also has offices located around the world to help address your support needs. For telephone support in the United States, create your service request at ni.com/...
Need help?
Do you have a question about the WSN-3295 and is the answer not in the manual?
Questions and answers