Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ayrton AYM-09P
Summary of Contents for Ayrton AYM-09P
- Page 1 AYM -09P Local airconditioner...
-
Page 2: Table Of Contents
Content Operation Notices The Refrigerant ......................1 Safety Warning ......................2 Operation Environment ....................3 Part's Name ......................4 Operation Guide Operation Introduction for Control Panel ..............5 Buttons on Remote Controller .................7 Introduction for Icons on Display Screen ..............7 Introduction for Buttons on Remote Controller ............8 Function Introduction for Combination Buttons ............10 Operation Guide .................... - Page 3 Explanation of Symbols Indicates a hazardous situation that, if not avoided, will DANGER result in death or serious injury. Indicates a hazardous situation that, if not avoided, could WARNING result in death or serious injury. Indicates a hazardous situation that, if not avoided, may CAUTION result in minor or moderate injury.
-
Page 4: The Refrigerant
Appliance filled with flammable gas R290. Before install and use the appliance, read the owner’s manual first. Before install the appliance, read the installation manual first. Before repair the appliance, read the service manual first. The Refrigerant To realize the function of the air conditioner unit, a special refrigerant circulates in the system. -
Page 5: Safety Warning
Safety Warning ● This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. -
Page 6: Operation Environment
Safety Warning ● Do not use an extension cord. ● Do not through sundries into the air duct. If there are sundries get into the air duct, please contact the professionals to deal with it. Operation Environment ● The air conditioner must be operated within the temperature range: 16°C ~ 35°C. -
Page 7: Part's Name
Part's Name Controller panel Swing louver Guide louver Castor Filter Joint Heat discharge pipe Joint D Joint C Plug of power cord Wire-fixing hook Remote controller NOTICE: Heat discharge pipe and other installation accessories can't be discarded. -
Page 8: Operation Introduction For Control Panel
Operation Introduction for Control Panel Name of control panel Dual-8 nixie tube Cool mode indicator + / - button Dry mode indicator Fan speed indicator Fan mode indicator Swing button Timer button Mode button ON/OFF button Fan button Operation of control panel Note: After putting through the power, the air conditioner will give out a sound. - Page 9 Operation Introduction for Control Panel Mode button Press this button and the mode will circulate according to below sequence: COOL→DRY→FAN COOL: Under this mode, cooling mode indicator is bright. Dual-8 nixie tube displays set temperature. Temperature setting range is 16°C~30°C. DRY: Under this mode, drying mode indicator is bright.
-
Page 10: Buttons On Remote Controller
Buttons on Remote Controller Note: This remote controller is the universal remote controller. Some function is not avail- able for this unit. ON/OFF button MODE button +/- button FAN button SWING button SLEEP button TIMER button Introduction for icons on display screen Timer on Timer off Sending signal... -
Page 11: Introduction For Buttons On Remote Controller
Introduction for buttons on remote controller Note: ● When power is connected(stand by condition), you can operate the air conditioner through the remote controller. ● When unit is on, each time you press the button on remote controller, the sending signal icon "... - Page 12 Introduction for buttons on remote controller FAN button Pressing this button can select fan speed circularly as: AUTO, SPEED 1 ( SPEED 2 ( ), SPEED 3 ( ), SPEED 4 ( ) (unavailable in this air conditioner. Speed 4 is the same with speed 3.). AUTO SPEED 1 (equals to low fan speed) SPEED 2 (equals to medium fan speed)
-
Page 13: Function Introduction For Combination Buttons
Introduction for Buttons on Remote Controller Note: ● Range of time setting is: 0.5~24h ● The interval between two motions can't exceed 5s, otherwise the remote con- troller will exit setting status. Function introduction for combination buttons Child lock function Press “+”... -
Page 14: Operation Guide
Operation Guide After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT. Press "+" or "-" button to set your required temperature. (Temperature can’t be adjusted under auto mode). -
Page 15: Clean And Maintenance
Clean and Maintenance WARNING ● Before cleaning the air conditioner, please turn off the unit and disconnect power. Otherwise, it may cause electric shock. ● Do not wash air conditioner with water. Otherwise, it may cause electric shock. ● Do not use volatile liquid (such as thinner or gas) to clean the air conditioner. Otherwise, it may damage the appearance of air conditioner. - Page 16 Clean and Maintenance Clean heat discharge pipe Remove the heat discharge pipe from air conditioner, clean and dry it , and then reinstall it. (For the method of installation and removal , please refer to the instruction for "Installation and disassembly of heat discharge pipe"). Checking before use-season 1.
-
Page 17: Malfunction Analysis
Malfunction Analysis Please check below items before asking for maintenance. If the malfunction still can’t be eliminated, please contact local dealer or qualified professionals. Phenomenon Troubleshooting Solution ● Power failure? ● Wait after power recovery. ● Is plug loose? ● Reinsert the plug. ●... - Page 18 Malfunction Analysis Phenomenon Troubleshooting Solution ● Whether air outlet or air inlet is ● Eliminate the obstacles. blocked? ● Under heating mode, whether ● The unit will stop blowing indoor temperature ireaches fan after reaching set set temperature? temperature. ● In order to prevent cold air, No air blowed ●...
- Page 19 Malfunction analysis Malfunction code ERROR Troubleshooting CODE Please contact qualified professionals for service. Please contact qualified professionals for service. Please contact qualified professionals for service. Please contact qualified professionals for service. 1.Check if the unit is under high-temperature and high-humidity environment; if ambient temperature is too high, power off the unit and then energize it for operation after the ambient temperature drops to 35 below.
-
Page 20: Installation Precaution
Installation Precaution WARNING ● Observe all governing codes and ordinances. ● Do not use damaged or non-standard power cord. ● Be caution during installation and maintenance. Prohibit incorrect operation to prevent electric shock, casualty and other accidents. Selection of installation location Basic requirement Installing the unit in the following places may cause malfunction. - Page 21 Installation Precaution Requirements for electric connection WARNING: Safety precaution 1. Must follow the electric safety regulations when installing the unit. 2. According to the local safety regulations, use qualified power supply circuit. 3. For appliances with type Y attachment,the instructions shall contain the substance of the following.If the supply cord is damaged,it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
-
Page 22: Preparation Before Installation
Preparation before Installation Note: check if the accessories are available before installation. Accessory list joint A joint C joint D joint E Plastic Cover pipe clip pipe hoop screw wire hook rubber plug heat discharge pipe battery Adapter (AAA 1.5V) user's manual drainage pipe remote controller... -
Page 23: Install Wire Hook
Install Wire Hook ● Assemble the wire hook at the back of the unit with screws (the direction of wire hook is as shown in following fig). direction of wire hook is upward wire hook screw direction of wire hook is downward ●... -
Page 24: Removing Collected Water
Removing Collected Water There are 2 ways to remove collected water: Use the continuous drainage option from the bottom hole Note: When using the continuous drainage option from the bottom hole, drainage pipe before using, otherwise poor drainage will affect normal operation of the unit. - Page 25 Removing Collected Water ■ Drainage way as follows. 1. In Cool or Dry mode operating, the condensation water will be drained to the chassis. 2. When the chassis is full with water, the buzzer will give out 8 sounds and "H8" is displayed to remind user to discharge water,the unit will turned off about 2min latter, and all buttons are invalid.
- Page 26 Removing Collected Water Use the continuous drainage option from the middle hole Note: Water can be automatically emptied into a floor drain by attaching 14mm inner diameter hose (not included). Remove the continuous drain cap 1 by turning it counter clockwise then remove the rubber stopper 2 from the spout.
-
Page 27: Installation And Disassembly Of Heat Discharge Pipe
Installation and Disassembly of Heat Discharge Pipe 1. Installation of the heat discharge pipe in sliding window 1. Fold the rear join inwards unit these two clasps have tightly connected the rear joint together. 2. Rotate joint A and joint D clockwise into the two ends of heat discharge pipe. joint D heat discharge pipe clockwise... - Page 28 Installation and Disassembly of Heat Discharge Pipe 2. Installation of the heat discharge pipe in immovable window： 1. Rotate joint A and joint D clockwise into the two ends of heat discharge pipe. clockwise joint D clockwise heat discharge pipe joint A 2.
- Page 29 Installation and Disassembly of Heat Discharge Pipe 2. Installation of the heat discharge pipe in immovable window 4. Insert joint A of heat discharge pipe (the side with "TOP" is upwards) into the groove until you hear a sound. clasp the side with "TOP"...
- Page 30 Installation and Disassembly of Heat Discharge Pipe Note of Installingheat discharge pipe The discharge pipe is suggested to be installed according to below figure by the manufacturer. correct under 51 inchs about 24 inchs User can adjust the installation method of the discharge pipe basing on the requirement, while the similar installation methods as below which will lead to unsmoothly air-out are not allowed.
- Page 31 Installation and Disassembly of Heat Discharge Pipe Disassemble heat discharge pipe 1. Disassembly of the heat discharge pipe in sliding window: 1. Remove joint A: 2. Remove joint D: Press the clasp and lift joint A upwards to remove joint D from joint C. remove it.
- Page 32 Installation and Disassembly of Heat Discharge Pipe 2. Remove the heat discharge pipe from the Joint D. Anti-clockwise 3. When heat discharge pipe is removed, Install the plastic cover into Joint D in case of the insect into the house . Clockwise Plastic Cover...
-
Page 33: Operation Test
Operation Test ● Put through the power supply and then press ON/OFF button on remote contro- ller to start the unit. ● Press mode button to select auto, cooling, drying, fan or heating function, and then check if the unit operates normally. ●...
Need help?
Do you have a question about the AYM-09P and is the answer not in the manual?
Questions and answers